Engine Oil Scavenge Pump
Show/hide table
图 1 | g03836650 |
Show/hide table
技术规格 - 144-8267 发动机扫油泵 | |||
---|---|---|---|
项目 | 数量 | 零件 | 技术规格说明 |
从驱动端观看扫油泵时,驱动装置按逆时针方向旋转。 | |||
1 | 4 | 3H-2750 螺栓 | 拧紧至扭矩为 |
2 | 2 | 237-7623 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
Show/hide table
图 2 | g03836651 |
剖面 A-A |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
---|---|---|---|
3 | 1 | 0S-0484 螺栓 | 采用下述步骤拧紧螺栓: 将驱动齿轮安装到驱动轴组件前,用异丙醇清洁轴和齿轮孔。 1. 敲打驱动齿轮以座合驱动齿轮的锥形部分。 2. 拧紧螺栓至扭矩 3. 重复步骤 1 和步骤 2,直到扭矩不变。 |
A | 1 | 144-8272 齿轮 | 新齿轮的长度为 扫油泵体中新齿轮孔的深度为 |
B | 1 | 161-2511 驱动轴 | 新驱动轴的直径为 套筒轴承中新驱动轴的孔径为 |
C | 1 | 144-8270 惰轮轴 | 新惰轮轴的直径为 套筒轴承中新惰轮轴的孔径为 |
D | 2 | 1W-6005 衬套 | 衬套在 144-8265 扫油泵体上的安装深度为 |
Show/hide table
图 3 | g03836653 |
Show/hide table
图 4 | g03836655 |
Show/hide table
注意 |
---|
操作之前,必须使用干净的发动机机油润滑泵体,并且泵必须能灵活运转,否则就会导致部件的损坏。 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
---|---|---|---|
E | - | - | 从中线穿过轴承孔的轴承接头位置为 45 ± 15 度。 |
F | 2 | 4M-3248 空心定位销 | 空心定位销自扫油泵盖的延伸长度为 |
G | 2 | 1W-6005 衬套 | 7N-8814 扫油泵盖上的衬套安装深度为 |
Caterpillar Information System:
3512B SR4B Generator Sets Emergency Stopping
Frequently Asked Questions about Oil Emulsion{1000, 1317, 1348} Frequently Asked Questions about Oil Emulsion{1000, 1317, 1348}
345D, 349D and 349D2 Excavators Hydraulic System Fan Pump (Hydraulic and Radiator Cooling)
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Alternate Exit
345D, 349D and 349D2 Excavators Hydraulic System Bypass Valve (Return) - Bypass Check Valve
C175-16 and C175-20 Generator Set Engines Prelubrication - Test
345D, 349D and 349D2 Excavators Hydraulic System Check Valve (Return Makeup)
345D, 349D and 349D2 Excavators Hydraulic System Return Hydraulic System
C175-16 and C175-20 Generator Set Engines Speed/Timing - Test
C175-16 and C175-20 Generator Set Engines Turbocharger Turbine Temperature Is High
C18 Generator Set Engines Oil Temperature Is High
C15 and C18 Petrolem Generator Set Engines Oil Pressure Is Low
C175-16 and C175-20 Generator Set Engines Fuel Control - Test
C13T-TH35 and C15T-TH35 Petroleum Packages Plate Locations and Film Locations
345D, 349D and 349D2 Excavators Hydraulic System Electronic Control System
345D, 349D and 349D2 Excavator Machine System Specifications Pump Lines (Main)
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Check Valve
C15 Petroleum Generator Set Engines Speed/Timing Sensor
3500 Engines with EUI Option Flywheel Housing
C175-16 and C175-20 Generator Set Engines Gear Group (Front)
2008/03/01 A New Procedure for Installing the Internal Wiring Harness is Now Used {1120, 1408}
C175-16 and C175-20 Generator Set Engines Coolant Temperature Is High
C175-16 and C175-20 Generator Set Engines Coolant Temperature Is Low
C175-16 and C175-20 Generator Set Engines Exhaust Temperature Is High