Housing (Front) - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-8440 | Component Cleaner | 1 |
B | 4C-9500 | Quick Cure Primer | 1 |
C | 1U-8846 | Gasket Sealant | 1 |
- Clean the joint face on front housing (4) with Tooling (A).
- Apply Tooling (B) to the joint face.
Note: Do not allow Tooling (C) to seal the main oil passage on front housing (4).
- Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (4) must be installed within ten minutes of applying the sealant.
- Position front housing (4) on the cylinder block.
- Install bolts (3).
- Install bolts (5).
Show/hide table
Illustration 2 g01151885 - Connect harness assemblies (1) and (2).
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 1 | g01151892 |
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
- Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Install the air compressor, if necessary. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
- Install the auxiliary water pump, if necessary. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
- Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install".
- Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
- Install the fan drive, if necessary. Refer to Disassembly and Assembly, "Fan Drive - Install".
Caterpillar Information System:
C15 and C18 Petroleum Generator Sets Speed Sensor - Clean/Inspect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Connect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Separate
C9 Petroleum Engines Housing (Front) - Remove
2007/12/03 Improved PL1000T Hardware and Software is Now Available {7610}
C3.3 Industrial Engine Model View Illustrations
C4.4 Generator Set Engines Injector Data Incorrect - Test
G3520B Industrial Engines Diagnostic Trouble Codes
G3520B Industrial Engines Event Codes
3176C, 3406E and 3456 Industrial Engines ECM Does Not Communicate with Other Modules
3516B Engine for 994F and 994H Wheel Loaders Coolant Contains Oil
2007/11/26 Improved PL1000E Hardware and Software is Now Available {7610}
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Remove
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Disassemble
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Assemble
C4.4 Generator Set Engines Injector Solenoid Circuit - Test
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
C9 Petroleum Engines Crankcase Breather - Remove and Install
G3600 Engines Sensor Signal (PWM) - Test
C9 Petroleum Engines Cylinder Block Cover - Remove and Install
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Fasteners
G3600 Engines Fuel Control - Test
320D and 323D Excavators Hydraulic System Swing Drive