Vibration Damper - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-9392 (1)     | Damper Guide Pin     | 2     |
1U-9393 (1) | Damper Guide Pin     | 2     | |
4C-9426 (1) | Damper Guide Pin     | 2     | |
B     | 8T-0914     | Flywheel Guide Pin     | 2     |
Show/hide table
( 1 ) | All of the guide pins are available. The particular guide pin that is required depends on your application. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove two bolts (2) that hold vibration damper (1) to the shaft. Install Tooling (A) in the holes.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Show/hide table
Illustration 1 | g00556435 |
- Remove the remainder of bolts (2). Carefully move vibration damper (1) onto Tooling (A) in order to pass a suitable lifting device through the center of vibration damper (1) .
- Attach a suitable lifting device to vibration damper (1). The weight of vibration damper (1) is approximately 188 kg (414 lb). Remove vibration damper (1) .
- Remove two of the bolts that hold adapter (3) in place. Install Tooling (B) in the holes.
Show/hide table
Illustration 2 | g00556436 |
- Remove the remainder of the bolts. Carefully move adapter (3) onto Tooling (B) in order to pass a suitable lifting device through the center of adapter (3) .
- Attach a suitable lifting device to adapter (3). The weight of adapter (3) is approximately 30 kg (66 lb). Remove adapter (3) .
Note: For information on rebuilding vibration dampers, refer to Reuse and Salvage Guidelines, SEBF8152, "Procedures to Rebuild Vibration Dampers for 3600 Family of Engines".
Caterpillar Information System:
3608 Engine Rocker Arm - Disassemble
2007/10/22 The Programmable Monitoring System Parameters Have New Descriptions {1901, 1902, 7620}
3608 Engine Valve Mechanism - Install
3608 Engine Camshaft - Remove
2007/10/15 An Improved Air Cleaner Assembly is Now Used {1051, 1054}
2007/10/01 A New Base for the Engine Oil Cooler and Engine Oil Filter is Now Used {1306, 1378}
3176C and 3196 Engines for Caterpillar Built Machines Exhaust Manifold
3176C and 3196 Engines for Caterpillar Built Machines Exhaust Manifold
3608 Engine Idler Gears (Rear) - Install
3608 Engine Idler Gears (Rear) - Remove
3608 Engine Crankshaft Rear Seal - Install
C15 and C18 Petrolem Generator Set Engines Cat Data Link - Test
C-10 and C-12 Truck Engines Exhaust Manifold
C-10 and C-12 Truck Engines Exhaust Manifold
3608 Engine Crankcase Explosion Relief Valve - Remove and Install
3608 Engine Governor - Remove
3608 Engine Governor - Install
3500B and 3500C Marine Propulsion Engines Engine Will Not Crank
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073} Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073}
3608 Engine Governor Drive - Assemble - Later
3608 Engine Fuel Injector - Remove
3608 Engine Fuel Injector - Install
C15 and C18 Petrolem Generator Set Engines Sensor Signal (Analog, Active) - Test