Exhaust Manifold - Remove and Install - C280-6
Start By:
- Remove the exhaust manifold shields. Refer to Disassembly and Assembly, "Exhaust Manifold Shield - Remove and Install".
- Disconnect the thermocouples from the segments of the exhaust manifold that are being removed.
- Remove adapters (7), if necessary.
- Loosen bolts (4) that mount exhaust manifold (5) to the cylinder head from the segment of the exhaust manifold that is on the end. Loosen bolts (1) that mount the segment of the exhaust manifold that is on the end to bellows (2). Loosen bolts (3) that mount bellows (2) that is on the end to the adjacent exhaust manifold.
- Repeat Step 1 through Step 3 for the remaining segments of exhaust manifold (5). Move toward the turbocharger when you are loosening all of the remaining bolts.
- Return to the segment of the exhaust manifold that is on the end. Attach a suitable lifting device to the segment of the exhaust manifold. The weight of each segment of exhaust manifold (5) is approximately
25 kg (55 lb) . - Remove bolts (4) that mount exhaust manifold (5) to the cylinder head from the segment of the exhaust manifold that is on the end. Remove bolts (1) that mount the segment of the exhaust manifold that is on the end to bellows (2). Remove the segment of exhaust manifold (5). Remove the gasket. Remove bolts (3) that mount bellows (2) that is on the end to the adjacent exhaust manifold. Remove the bellows.
- Repeat Step 5 and Step 6 for the remaining segments of exhaust manifold (5). Move toward the turbocharger when you are removing all of the remaining bolts. Brackets (6) will come apart as the bolts for the exhaust manifold and the bolts for the bellows are removed.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 1 | g01315562 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5P-3931 | Anti-Seize Compound | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not preassemble the exhaust system before installation of the engine. Damage to the bellows could result. |
- Apply Tooling (A) to the threads of the bolts of the exhaust manifold, the washers, the bolts of the bellows, the plugs and the adapters before installation.
Show/hide table
Illustration 2 g01315562 - Attach a suitable lifting device to a segment of the exhaust manifold. The weight of each segment of exhaust manifold (5) is approximately
25 kg (55 lb) . Position the gasket and exhaust manifold (5) on the cylinder head. Install bolts (4) that mount the exhaust manifold to the cylinder head. Tighten the bolts finger tight.Note: Do not tighten these bolts to the torque specification at this time.
- Repeat Step 2 for all segments of exhaust manifold (5).
- Install bellows (2), bolts (3), and bolts (1) on exhaust manifold (5). Tighten the bolts finger tight.
- Install brackets (6) on the exhaust manifold.
- Tighten bolts (4) that mount exhaust manifold (5) to the cylinder head to a torque of
135 ± 20 N·m (100 ± 15 lb ft) . - Tighten bolts (1) and bolts (3) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . Ensure that the bolts for brackets (6) are tightened. - If adapters (7) were removed, tighten adapters (7) to a torque of
200 ± 25 N·m (150 ± 20 lb ft) .
End By:
- Install the exhaust manifold shields. Refer to Disassembly and Assembly, "Exhaust Manifold Shield - Remove and Install".
Caterpillar Information System:
C280-12 and C280–16 Marine Engines Exhaust Manifold - Remove and Install - C280-16
C280-12 and C280–16 Marine Engines Exhaust Manifold - Remove and Install - C280-12
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Control
3512C and 3516C Marine Auxiliary and Generator Set Engines Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
3512C and 3516C Marine Auxiliary and Generator Set Engines Maintenance Recommendations
3512C and 3516C Marine Auxiliary and Generator Set Engines Safety Messages
Installation Instructions For UPS 1200 With Paralleling{4480} Installation Instructions For UPS 1200 With Paralleling{4480}
3608 Engine Crankshaft - Install
UPS 1000S and UPS 1200S Uninterruptible Power Supplys , Parallel Serial Number Plate
3608 Engine Crankshaft - Remove
C280-6 and C280-8 Engines Crankshaft - Install
3606 and 3608 Engines Crankshaft - Install
C280-6 and C280-8 Engines Exhaust Manifold - Remove and Install - C280-8
TA19-M2WD and TA19-M4WD Agricultural Transmissions Lifting and Tying Down the Transmission
TA19-M2WD and TA19-M4WD Agricultural Transmissions Capacities (Refill)
TA19-M2WD and TA19-M4WD Agricultural Transmissions Breather (Transmission) - Clean
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil - Change
Bench Test Procedure For A TH48FT - E70 Oil Field Transmission {3030} Bench Test Procedure For A TH48FT - E70 Oil Field Transmission {3030}
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Oil Level - Check
TA19-M2WD and TA19-M4WD Agricultural Transmissions Transmission Suction Screen - Clean
C0.5 and C0.7 Industrial Engines Fuel Injector - Test/Change
2006/11/13 New Software is Now Available for EMCP 3.1, EMCP 3.2, and EMCP 3.3 {4490, 7620}
2006/10/16 New Software Available for Product Link {7606, 7620}
C280-12 and C280–16 Marine Engines Engine Lifting Bracket - Remove and Install