Electric Starting Motor - Remove and Install
Show/hide table
发动机的意外起动会对在设备上工作的人员造成伤害或死亡。 |
- 断开蓄电池。
- 在连接电动起动马达的线束组件上做出临时的识别标记。
Show/hide table
图 1 g01326136 典型示例 - 从电动起动马达 (2) 上断开线束组件(未显示)。
- 拆下固定电动起动马达 (2) 的紧固件 (1)。
注: 在拆卸紧固件的过程中,支撑住电动起动马达的重量。
- 从发动机上拆下电动起动马达 (2)。
- 将电动起动马达 (2) 在发动机上安装入位。
- 安装紧固件 (1) 并紧固至扭矩
50 N·m (37 lb ft) 。 - 将线束组件(未显示)连接在电动起动马达 (2) 上。
- 连接蓄电池。
Show/hide table
图 2 | g01326136 |
典型示例 |
Caterpillar Information System:
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C27 and C32 Generator Set Engines Engine Support (Rear)
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
C15 On-Highway Engine Exhaust Manifold
C15 On-Highway Engine Exhaust Manifold
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Housing (Front) - Install