Crankshaft Pulley - Remove and Install
开始:
- 拆下 V 形皮带。 有关更多资料,请参阅拆解和组装, " V 形皮带 - 拆卸和安装"。
Show/hide table
所需工具 | |||
工具 | 零件号 | 说明 | 数量 |
A | 8S-2264 | 拉拔器总成 | 1 |
- | 螺栓 | 3 |
- 松开螺母 (3)。
注: 此时不要拆下螺母。
Show/hide table图 2 g01305772 - 将工具 (A) 安装到曲轴皮带轮 (2) 上。 使用工具 (A) 将曲轴皮带轮 (2) 从曲轴 (4) 上拆下。 拆下工具 (A)。
- 拆下螺母 (3)。
- 从曲轴 (4) 上拆下皮带轮 (2)。
- 从曲轴 (4) 上拆下半圆键 (1)。
Show/hide table
图 1 | g01326646 |
典型示例 |
- 确保下列部件干净、无损坏:曲轴的锥面、半圆键和曲轴皮带轮孔。 更换任何损坏的部件。 在组装之前,确保曲轴锥面和曲轴皮带轮孔清洁、干燥。
Show/hide table
图 3 g01326646 典型示例 - 将半圆键 (1) 安装到曲轴 (4) 上。
- 将曲轴皮带轮 (2) 安装到曲轴 (4) 上。
- 用清洁的发动机机油润滑螺母 (3),然后安装此螺母。
对于 C0.5 和 C0.7 发动机,将螺母 (5) 紧固至扭矩
93 N·m (69 lb ft) 。对于 C1.1 和 C1.6 发动机,将螺母 (5) 紧固至扭矩
123 N·m (91 lb ft) 。对于 C1.5 和 C2.2 发动机,将螺母 (5) 紧固至扭矩
304 N·m (224 lb ft) 。
结束:
- 将 V 形皮带安装到发动机上。 请参阅拆解和组装, " V 形皮带 - 拆卸和安装"。
Caterpillar Information System:
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C27 and C32 Generator Set Engines Engine Support (Rear)
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
C15 On-Highway Engine Exhaust Manifold
C15 On-Highway Engine Exhaust Manifold
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
G3520C and G3520E Generator Set Engines Ignition Secondary - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Disassemble