Gear Pump (Torque Converter and Transmission) - Remove
拆卸步骤
开始:
- 如有必要，拆解缓速器液压控制阀。 请参阅拆解和组装, "缓速器液压控制阀 - 拆卸和安装"。
- 如有必要，拆下控制歧管。 请参阅拆解和组装, "控制歧管 - 拆卸"。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前，应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
| 注意 |
|---|
在进行检验、保养、测试、调整及维修产品期间，必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前，要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品，请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 拆下螺栓 (1) 和盖 (2) 。
Show/hide table
 | |
| 图 1 | g01228322 |
- 拆下磁性滤清器 (3) 和滤网 (4) 。
Show/hide table
 | |
| 图 2 | g01228323 |
- 拆下螺栓 (5) 和油底壳 (6) 。
Show/hide table
 | |
| 图 3 | g01228324 |
- 拆下管组件 (9) 和 (10) 。
Show/hide table
 | |
| 图 4 | g01228325 |
- 拆下螺栓 (12) 和滤网壳体 (11) 。
- 如有配备，拆卸后 PTO 轴。
- 拆下螺栓 (7) 和齿轮泵 (8) 。
Caterpillar Information System:
3512B Oil Well Servicing Engine (ADEM III) Emergency Stop Switch
C7 Marine Engine Jacket Water Heater
C7 Marine Engine Crankshaft Pulley
C7 Marine Engine Exhaust Elbow
2013/08/21 Reminder for Troubleshooting Electronic Actuators {1130}
C7 Marine Engine Electronic Control Module
3512B Oil Well Servicing Engine (ADEM III) Coolant Temperature Is Too High
3512B Oil Well Servicing Engine (ADEM III) Excessive Black Smoke
3512B Oil Well Servicing Engine (ADEM III) Exhaust Temperature Is Too High
3512B Oil Well Servicing Engine (ADEM III) Intermittent Engine Shutdown
3512B Oil Well Servicing Engine (ADEM III) Intermittent Low Power or Power Cutout
3512B Oil Well Servicing Engine (ADEM III) Low Engine Oil Pressure
320D and 323D Excavators Machine System Specifications Main Control Valve
2008/02/11 New Injectors are Being Offered in Place of Remanufactured Injectors {1290}
CX31 On-Highway Transmission Power Train Gear Pump (Torque Converter and Transmission) - Install
C175 Generator Set Engines Camshaft - Install
C6.6 Generator Sets Plate Locations and Film Locations
3512B Oil Well Servicing Engine (ADEM III) Speed Control
C7 Marine Engine Electric Starting Motor
C7 Marine Engine Electric Starting Motor
3512B Oil Well Servicing Engine (ADEM III) Pulse Width Modulated Sensor
CX31 On-Highway Transmission Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
3500 Engines Fan Drive - Install