Engine Performance - Test - Engine Speed
Show/hide table
314E CR/SR (LHP) | ||||||||
---|---|---|---|---|---|---|---|---|
"Engine Performance - Test (Engine Speed)" | ||||||||
Conditions | Specifications (HP mode) | |||||||
Engine | "AEC" Switch Position | "Engine Speed Dial" Position | Time (sec) | New | Rebuild | Service Limit | Actual | |
No load | OFF | 10 | 0 to 5 | 1600 ± 50 rpm(1) | 1450 to 1700 rpm(1) | |||
OFF | 10 | > 5 | 1600 ± 50 rpm | 1450 to 1700 rpm | ||||
ON | 10 | > 5 | 1000 ± 50 rpm | 1000 ± 100 rpm | ||||
OFF | 1 | > 5 | 900 ± 50 rpm | 900 ± 100 rpm | ||||
One touch low idle | > 0 | 1000 ± 50 rpm | 1000 ± 100 rpm | |||||
Load(2) | OFF | 10 | > 3 to 5 | Implement | 1700 ± 50 rpm | ≥ 1600 rpm | ||
Travel | 1800 ± 50 rpm | ≥ 1700 rpm |
Show/hide table
(1) | ODEP "ON" |
(2) | Two pump main relief (Boom UP operation). |
Note: A New specification is the performance that can be expected for a new machine. A Rebuild specification is the performance that can be expected after rebuilding the components of a system. Performance beyond the Service Limit is an indication of these problems: improper maintenance or adjustment, component wear and failure.
The following test is used to measure engine speed at the flywheel housing.
Show/hide table
Illustration 1 | g02535237 |
Tooling (C) |
Show/hide table
Tooling | Item | QTY | Part
Number |
Description |
---|---|---|---|---|
C | 348-5430 | Multi-Tool Gp | ||
C1 | 1 | 285-0908 | Multi-Tool | |
C2 | 1 | 6V-2198 | Cable As | |
C3 | 1 | 9U-5140 | Photo Pickup | |
C4 | 1 | 6V-3137 | Base | |
C5 | 1 | 1U-6605 | Reflective Tape | |
C6 | 1 | 6V-3138 | Extension |
Reference: Refer to Tool Operating Manual, NEHS1087 for operating instructions for the 348-5430 Multi-Tool Gp.
Note: Use Software License Card, NETG5049 with part number 348-5430 Multi-Tool Gp.
- Position the machine on level ground.
- Stop the engine.
- Install tooling (C) on the engine.
- Start the engine.
- Increase the hydraulic oil temperature to
55° ± 5°C (131° ± 9°F) . - Read the engine speed display (rpm) on the multi-tool. Refer to Table 1 for the specifications for engine speed at the desired engine operation.
Caterpillar Information System:
336E H Excavator Electrical Power Supply - Test
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Main Hydraulic Pump Mounting
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Flywheel Housing
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Flywheel
330F MHPU Mobile Hydraulic Power Unit Machine System Control Valve - Boom Regeneration
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Connecting Rod
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Main Bearing Journal
336E Excavator Machine System Specifications Pilot Lines - Stick Lowering Control
336E Excavator Machine System Specifications Pilot Lines - Stick Lowering Control
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Cylinder Head
336E Excavator Machine System Specifications Pilot Lines
336E Excavator Machine System Specifications Pilot Lines
Procedure to Install the 418-0310 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators {5057, 5362, 6547} Procedure to Install the 418-0310 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators {5057, 5362, 6547}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Set
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Calibrate
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Accuracy - Test
336F MHPU Mobile Hydraulic Power Unit Machine Systems Pump Control (Main Hydraulic)
Procedure to Install the 418-0311 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057, 5362, 6547} Procedure to Install the 418-0311 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057, 5362, 6547}
Procedure to Install the 418-0312 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057} Procedure to Install the 418-0312 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057}
Procedure to Install the 420-3637 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057} Procedure to Install the 420-3637 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057}
Procedure to Install the 420-3638 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057} Procedure to Install the 420-3638 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057}
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Main Control Valve
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Main Control Valve
301.7D, 302.2D and 302.4D Mini Hydraulic Excavator Machine Systems Main Control Valve