Pistons and Connecting Rods - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 8S-2269     | 缸口铰刀     | 1     |
开始:
- 拆下吸油管。 有关正确步骤,请参阅拆解和装配, "发动机油底壳 - 拆卸和安装"。
- 如有必要,拆下平衡器。 有关正确步骤,请参阅拆解和装配, "平衡器 - 拆卸"。
- 拆下缸盖。 有关的正确程序,请参阅拆解与组装, "缸盖 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 旋转曲轴,直到所需的连杆处于下止点。
- 使用工具 (A) 清除缸径顶部的积碳。
- 连杆和连杆盖在位置 (X) 应该有蚀刻的编号。 连杆和连杆盖上的编号必须相互匹配。 确保标记连杆 (3) 和连杆盖 (1) 的正确位置。 如有必要,在连杆和连杆盖上做出一个临时的标记来识别缸号和组件的方位。
Show/hide table
图 1 | g03001196 |
典型示例 |
注: 请勿压印连杆组件。 在连杆组件上压印或冲孔会导致连杆断裂。
- 拆下螺栓 (2) 并将连杆盖 (1) 从连杆 (3) 上拆下。
- 旋转曲轴,使所需的活塞处于上止点。
- 小心地把活塞 (4) 和连杆推出缸孔。 将活塞 (4) 抬出缸体顶部。
注: 不要推压连杆的断面分裂面,否则会导致损坏。
Show/hide table
图 2 | g02998516 |
典型示例 |
- 从发动机上取出组件后,暂时将连杆盖 (1) 和螺栓 (2) 安装到连杆 (3) 上。 确保连杆盖与连杆上的蚀刻编号相互匹配。 确保连杆盖的朝向正确。 上下轴瓦的定位凸舌应在同一侧。 将螺栓 (2) 拧紧至 20 N·m (177 lb in) 的扭矩。
- 重复步骤 1 至步骤 7,以便拆下其余的活塞和连杆。
放置断面分裂式连杆时必须要安装连杆盖。
Caterpillar Information System:
329F and 330F Excavators Machine System Specifications Pilot Lines
320E and 323E Excavators Machine System Specifications Pilot Lines
C2.6 and C3.3B Engines for Caterpillar Built Machines Fan Drive
C2.6 and C3.3B Engines for Caterpillar Built Machines Engine Oil Cooler
314E CR and 314E SR Excavator Systems Bucket System
C2.6 and C3.3B Engines for Caterpillar Built Machines Cylinder Head
C2.6 and C3.3B Engines for Caterpillar Built Machines Water Temperature Regulator
314E CR and 314E SR Excavator Systems Stick System
C13, C15, and C18 Tier 4 Final Engines Mounting Frame
Hydraulic Thumbs Thumb - Lubricate
Hydraulic Thumbs Lifting and Tying Down
Hydraulic Thumbs Shipping
C2.6 and C3.3B Engines for Caterpillar Built Machines Valve Mechanism Cover
C2.6 and C3.3B Engines for Caterpillar Built Machines Cylinder Head Valves
C2.6 and C3.3B Engines for Caterpillar Built Machines Valve Mechanism
321D LCR Excavator Machine System Specifications Pilot Lines
335F Excavator Machine System Specifications Blade Lift Cylinder
321D LCR Excavator Machine System Specifications Pilot Lines
C15 and C18 Engines for Caterpillar Built Machines Rocker Shaft
321D LCR Excavator Machine System Specifications Blade Cylinder Lines
340F Excavator Machine Systems Swivel
330F Excavators Machine System Specifications Pilot Lines
C3.4B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
325D and 329D Excavators Machine System Specifications Auxiliary Hydraulic Lines