Track Carrier Roller - Disassemble
Disassembly Procedure
Start By:
- Remove the track carrier rollers. Refer to Disassembly and Assembly, "Track Carrier Roller - Remove" in this manual.
- Thoroughly clean the outside of the track carrier roller prior to disassembly.
- Remove plug (2). Drain the oil from the carrier roller into a suitable container for disposal. The capacity of the track carrier roller is 85 ± 8 mL (2.89 ± .28 oz).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
Illustration 1 | g00365386 |
- Remove three socket head bolts (1) and cover (3) from the track carrier roller.
- Remove O-ring seal (4) from cover (3) .
Show/hide table
Illustration 2 | g00365954 |
- Remove socket head bolts (5) and (6) and retainer (7) from the end of the shaft assembly.
Show/hide table
Illustration 3 | g00365960 |
- Carefully remove shaft assembly (8) from the track carrier roller.
Show/hide table
Illustration 4 | g00365964 |
- Remove Duo-cone seal kit (9) from the track carrier roller.
Show/hide table
Illustration 5 | g00365965 |
- Remove Duo-cone seal kit (10) from shaft assembly (8) .
Show/hide table
Illustration 6 | g00367057 |
- Measure distance (X) on the shaft assembly. Record this dimension for assembly purposes. Use a press to push shaft (8) out of collar (11). Remove the O-ring seal from the inside of the collar.
Show/hide table
Illustration 7 | g00367112 |
- Remove bearings (12) and (13) from the track carrier roller.
Show/hide table
Illustration 8 | g00367133 |
Show/hide table
Illustration 9 | g00367312 |
Caterpillar Information System:
315B and 315B L Excavator Supplement For 3046 Engine Engine and Piston Pump - Remove
330B Excavator Hydraulic System Gear Pump (Pilot) - Test
M318 and M320 Excavators Machine System Specifications Control Valve (Boom Lowering)
315B Excavator Machine Systems Cab - Install
5130 Excavator Hydraulic System Check Valve (Swing and Travel Back Pressure)
315B and 315B L Excavator Supplement For 3046 Engine Coolant Tank (Expansion) - Remove and Install
330B Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
330B Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Install
330B Excavator Hydraulic System Pump Control (Output Flow) - Adjust
315B Excavator Machine Systems Cab - Remove
M315 Excavator Machine System Bucket Cylinder
M315 Excavator Machine System Boom Cylinder
330B Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
M312 Excavator Machine System Bucket Sidecutter
315B Excavator Machine Systems Undercarriage Frame - Install
M318 and M320 Excavators Machine System Specifications Flow Control Valve
M315 Excavator Machine System Boom Cylinder
307B Excavator Blade Control - If Equipped
315B Excavator Machine Systems Swing Gear and Bearing - Remove and Install
307B Excavator Windshield
318B Excavator Cab Door
M315 Excavator Machine System Boom Cylinder
315B Excavator Machine Systems Tank and Filter (Hydraulic) - Remove