Cab - Install
Installation Procedure
- Fasten a hoist to the lifting bracket on top of cab (24), as shown. Carefully position the cab on the platform. The weight of the cab is 288 kg (635 lb).
Show/hide table
Illustration 1 | g00480925 |
- Install nine bolts (22) that hold the cab to platform (23) .
Show/hide table
Illustration 2 | g00365052 |
- Connect electrical connectors (20) and (21) .
Show/hide table
Illustration 3 | g00364983 |
- Connect electrical connectors (18) and (19) .
Show/hide table
Illustration 4 | g00364982 |
- Put cover (16) in position at the rear of the cab. Install the washers and two bolts (17) that hold the cover in place.
Show/hide table
Illustration 5 | g00364978 |
- Put box (13) in position at the rear of the cab. Install four screws (14) .
Show/hide table
Illustration 6 | g00364952 |
- Install wiring harness (15) on the side of box (13) .
- Connect hose (12) to box (13) .
Show/hide table
Illustration 7 | g00364899 |
- Install cover (11) and four screws (10). Close rear compartment door (9) .
Show/hide table
Illustration 8 | g00364896 |
- Install four screws (8) in the cover at the rear of the cab.
Show/hide table
Illustration 9 | g00364838 |
- Connect air duct (7) to elbow (6) .
Show/hide table
Illustration 10 | g00364837 |
- Position cover (5) in the cab. Install three screws (4) .
Show/hide table
Illustration 11 | g00364832 |
- Carefully install rubber floormat (3) in the cab.
Show/hide table
Illustration 12 | g00364812 |
- Position guard (2). Install three screws (1) that hold the guard.
Show/hide table
Illustration 13 | g00364712 |
Caterpillar Information System:
5130 Excavator Hydraulic System Check Valve (Swing and Travel Back Pressure)
315B and 315B L Excavator Supplement For 3046 Engine Coolant Tank (Expansion) - Remove and Install
330B Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
330B Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Install
330B Excavator Hydraulic System Pump Control (Output Flow) - Adjust
315B Excavator Machine Systems Cab - Remove
M315 Excavator Machine System Bucket Cylinder
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Remove
315B Excavator Machine Systems Seat - Remove and Install
5230 Excavator Hydraulic System Hydraulic System Troubleshooting
315B Excavator Machine Systems Fuel Tank - Install
M318 and M320 Excavators Machine System Specifications Control Valve (Boom Lowering)
330B Excavator Hydraulic System Gear Pump (Pilot) - Test
315B and 315B L Excavator Supplement For 3046 Engine Engine and Piston Pump - Remove
315B Excavator Machine Systems Track Carrier Roller - Disassemble
M315 Excavator Machine System Boom Cylinder
330B Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
M312 Excavator Machine System Bucket Sidecutter
315B Excavator Machine Systems Undercarriage Frame - Install
M318 and M320 Excavators Machine System Specifications Flow Control Valve
M315 Excavator Machine System Boom Cylinder
307B Excavator Blade Control - If Equipped
315B Excavator Machine Systems Swing Gear and Bearing - Remove and Install