Aftercooler - Remove
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 排出后冷器/机油冷却器回路中的冷却液。
- 卸下后冷器出水管 (1) 。 卸下后冷器进水管 (2) 。
Show/hide table
图 1 | g00590232 |
G3606 发动机 |
Show/hide table
图 2 | g00590234 |
G3608 发动机 |
- 卸下六个螺栓 (3) 。
Show/hide table
图 3 | g00590237 |
G3606 发动机 |
Show/hide table
图 4 | g00590238 |
G3608 发动机 |
- 卸下法兰和管道 (4) 。 卸下安装螺栓和弯头 (5) 。
- 断开接头 (6) 上的连接器。
Show/hide table
图 5 | g00590243 |
典型实例 |
- 卸下将夹子固定至后冷器的四个螺栓 (7) 。 移开夹子固定的点火线。
- 从后冷器上卸下螺栓 (8) 、执行器和阻风门。 拆下垫片。
- 从后冷器水管上卸下适配器 (9) 。 从后冷器水管上卸下 O 形密封圈 (11) 和环 (10) 。
Show/hide table
图 6 | g00590245 |
典型实例 |
- 从后冷器上卸下两个适配器 (13) 和两个适配器 (12) 。 从适配器 (12) 上卸下 O 形密封圈。
Show/hide table
图 7 | g00590248 |
典型实例 |
- 使用防松螺母将 1/2 英寸的锻造吊环 (14) 安装在后冷器的顶部。
Show/hide table
图 8 | g00590249 |
- 将适当的起吊设备固定至锻造吊环上。 卸下固定后冷器的螺栓。 从缸体上卸下后冷器 (2) 。 G3606 发动机后冷器的重量约为 77 kg (170 lb)。 G3608 发动机后冷器的重量约为 101 kg (225 lb)。
- 检查后冷器芯四周的密封件 (15) 。 如果密封件损坏,则更换密封件。
Show/hide table
图 9 | g00590251 |
- 从后冷器芯管上卸下四个 O 型密封圈 (16) 。
- 检查空气室内是否有碎屑。 如果发现碎屑,请卸下检查盖并清洁空气室。 查找碎屑来源并进行修理。
Caterpillar Information System:
3406E and 3456 Generator Set Engines Electrical Ground Stud
G3500 Engines Engine Oil Pan - Disassemble
G3500B Engines Fuel Metering Valve Screen - Check
G3606 and G3608 Engines Air Inlet Elbow - Remove and Install
G3500 Engines Engine Oil Pan - Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Assemble
G3500 Engines Engine Oil Pan - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
3406E and 3456 Generator Set Engines Flywheel Housing
120H and 135H Motor Graders Hydraulic and Steering System Gerotor Motor (Circle Drive)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Sequence Valves - Remove and Install
G3606 and G3608 Engines Generator - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3606 and G3608 Engines Aftercooler - Install
G3500 Engines Engine Oil Pan - Assemble
G3500 Engines Engine Air Cleaner Service Indicator - Inspect
3406E and 3456 Generator Set Engines Exhaust Manifold
G3500 Engines Engine Oil and Water Pump Drive - Assemble
G3606 and G3608 Engines Air Inlet Choke - Remove
G3606 and G3608 Engines Air Inlet Choke - Disassemble
G3606 and G3608 Engines Air Inlet Choke - Assemble
G3500 Engines Engine Oil and Water Pump Drive - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Remove
3406E Generator Set Engines Refill Capacities