Engine Oil Pan - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺栓 3/8 - 16 NC     |
4     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保 O 形密封圈安装在发动机机油泵的适配器上,然后将干净的发动机机油涂抹到 O 形密封圈上。
- 将工具 (A) 安装到发动机油底壳中,然后安装密封垫。
- 将发动机抬到发动机油底壳上。 发动机有以下几种重量:
- G3508 发动机重量约为 4300 kg (9500 lb)。
- G3512 发动机重量约为 5443 kg (12000 lb)。
- G3516 发动机重量约为 6440 kg (14200 lb)。
- G3508 发动机重量约为 4300 kg (9500 lb)。
Show/hide table
图 1 | g01254661 |
典型示例 |
- 发动机油底壳有以下重量规格:
- G3508 发动机油底壳重量约为 295 kg (650 lb)。
- G3512 发动机油底壳重量约为 364 kg (800 lb)。
- G3516 发动机油底壳重量约为 393 kg (865 lb)。
- G3508 发动机油底壳重量约为 295 kg (650 lb)。
- 将螺栓 (2) 安装到发动机油底壳 (3) 上。
- 安装将发动机机油泵适配器固定到发动机油底壳的螺栓 (1) 。
注: 更多信息,请参阅规格, "发动机油底壳"。
Show/hide table
图 2 | g00590117 |
- 在发动机中加入正确油位的干净机油。 请参阅操作和保养手册, "发动机机油 - 更换"。
Caterpillar Information System:
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Assemble
G3500 Engines Engine Oil Pan - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
3406E and 3456 Generator Set Engines Flywheel Housing
120H and 135H Motor Graders Hydraulic and Steering System Gerotor Motor (Circle Drive)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Sequence Valves - Remove and Install
G3606 and G3608 Engines Generator - Remove and Install
G3606 and G3608 Engines Air Valve - Remove and Install
G3500 Engines Vibration Damper - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Disassemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
3116 Truck Engine Walk-Around Inspection
G3606 and G3608 Engines Air Inlet Elbow - Remove and Install
G3500B Engines Fuel Metering Valve Screen - Check
G3500 Engines Engine Oil Pan - Disassemble
3406E and 3456 Generator Set Engines Electrical Ground Stud
G3606 and G3608 Engines Aftercooler - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3606 and G3608 Engines Aftercooler - Install
G3500 Engines Engine Oil Pan - Assemble
G3500 Engines Engine Air Cleaner Service Indicator - Inspect
3406E and 3456 Generator Set Engines Exhaust Manifold
G3500 Engines Engine Oil and Water Pump Drive - Assemble
G3606 and G3608 Engines Air Inlet Choke - Remove