Engine Design
Show/hide table
 | |
| 图 1 | g00465539 |
气缸和气门位置 (A) 进气门 (B) 排气门 (C) 气体进入阀 | |
气缸数和气缸布置 ... 直列式8
每缸气门数
- 进气门 ... 2
- 排气门 ... 2
- 气体进入阀 ... 1
缸径 ... 300 mm (11.8 inch)
冲程 ... 300 mm (11.8 inch)
排量 ... 170 L (10,352 in)
压缩比 ... 9.2:1
压缩比 ... 11:1
燃烧方式 ... 火花点火
点火顺序
- 标准旋向逆时针(CCW) ... 1-6-2-5-8-3-7-4
气门间隙
- 进气门 ... 0.50 mm (0.020 inch)
- 排气门 ... 1.27 mm (0.050 inch)
- 气体进入阀 ... 0.64 mm (0.025 inch)
当从飞轮端观看曲轴时，曲轴以下述方向旋转。 ... 逆时针
注: 发动机的前端是与发动机飞轮端相对的发动机的另一端。 发动机的左、右侧是从发动机飞轮端来判断的。 #1缸是最前端的气缸。
Caterpillar Information System:
P16, P20, P25, P28, P40 and P60 Pulverizer Crusher Tooth and Cutting Edge Bolts - Tighten
Electronic Modular Control Panel II (EMCP II) for EUI Engines Normal Mode
Electronic Modular Control Panel II (EMCP II) for EUI Engines Modes Of Operation
Electronic Modular Control Panel II (EMCP II) for EUI Engines Electronic Control Module (Engine)
Electronic Modular Control Panel II (EMCP II) for EUI Engines Sensors
Electronic Modular Control Panel II (EMCP II) for EUI Engines Electrical Converter (Pulse Width Modulated)
C-10 and C-12 Truck Engines Electronic Control System
C-10 and C-12 Truck Engines Glossary of Electronic Control Terms
C-10 and C-12 Truck Engines Engine Design
3304B and 3306B Engines for Caterpillar Built Machines Automatic Timing Advance - Remove
Electronic Modular Control Panel II (EMCP II) for EUI Engines Instrument Panel
3306C Truck Engine Front Housing - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Alarm Mode
Electronic Modular Control Panel II (EMCP II) For MUI Engines Shutdown Mode
Electronic Modular Control Panel II (EMCP II) For MUI Engines Service Mode
Electronic Modular Control Panel II (EMCP II) For MUI Engines Fault Log Viewing OP1
Electronic Modular Control Panel II (EMCP II) For MUI Engines Engine/Generator Setpoint Viewing OP2
G3520C and G3520E Engines Flywheel Housing Cover
Electronic Modular Control Panel II (EMCP II) For MUI Engines Password Entry OP3
Electronic Modular Control Panel II (EMCP II) For MUI Engines Fault Log Clearing OP4
Electronic Modular Control Panel II (EMCP II) for EUI Engines Engine/Generator Programming OP5
Electronic Modular Control Panel II (EMCP II) for EUI Engines Spare Input/Output Programming OP6
Electronic Modular Control Panel II (EMCP II) for EUI Engines Hourmeter Programming OP7
G3606 and G3608 Engines Engine Supervisory System