SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Caterpillar


Contactor Group

Usage:

Low Pressure Oil Switch Assembly


Low Pressure Oil Switch Assembly (Left Side View)

(1) Seal

(2) Low pressure oil switch assembly. Tighten to a torque of ... 33 ± 7 N·m (24 ± 5 lb ft)

6T1546, 9X4276

Terminal No. 1 is common.

Terminal No. 2 is normally open.

Terminal No. 3 is normally closed.

With pressure increase, terminal 2 closes and terminal 3 opens at ... 93 ± 21 kPa (14 ± 3 psi)

With pressure decrease, terminal 2 opens and terminal 3 closes at ... 69 ± 21 kPa (10 ± 3 psi)

122-1522

Terminal No. 1 is common.

Terminal No. 2 is normally open.

Terminal No. 3 is normally closed.

With pressure increase, terminal 2 closes and terminal 3 opens at ... 76 ± 20 kPa (11 ± 3 psi)

With pressure decrease, terminal 2 opens and terminal 3 closes at ... 52 ± 17 kPa (8 ± 3 psi)

High Water Temperature Contactor Assembly


High Water Temperature Contactor Assembly (Rear View)

(1) High water temperature contactor assembly. Tighten to a torque of ... 75 ± 7 N·m (55 ± 5 lb ft)

(2) Seal

9Y1208

Terminal No. 1 is normally open.

Terminal No. 2 is common.

Terminal No. 3 is normally closed.

With temperature increase, terminal 2 closes and terminal 3 opens at ... 97 to 100°C (206 to 211°F)

With temperature decrease, terminal 2 opens and terminal 3 closes at ... 91°C (196°F)

7E8342

Terminal No. 1 is normally open.

Terminal No. 2 is common.

Terminal No. 3 is normally closed.

With temperature increase, terminal 2 closes and terminal 3 opens at ... 101 to 104°C (214 to 219°F)

With temperature decrease, terminal 2 opens and terminal 3 closes at ... 95°C (203°F)

Caterpillar Information System:

SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Hydraulic Pump Drive Mounting Group (Front)
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Heat Exchanger Group (Sea Water)
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Introduction
Caterpillar Electronic Locomotive Control System II 4 Discussion
Caterpillar Electronic Locomotive Control System II 3 Locomotive Electrical System Modification
Caterpillar Electronic Locomotive Control System II 2. Input-Output Connections
Caterpillar Electronic Locomotive Control System II 1. Mounting Plate Assembly
Caterpillar Electronic Locomotive Control System II Testing And Adjusting
Caterpillar Electronic Locomotive Control System II Problem Number 18 Engine Shuts Down
Caterpillar Electronic Locomotive Control System II Problem Number 17 Box Fault Lamp Is On
Caterpillar Electronic Locomotive Control System II Problem Number 16 Wheel Slip Lamp Is On
Caterpillar Electronic Locomotive Control System II Problem Number 15 Shutdown Lamp Is On
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Air Inlet Heater Group
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Water Temperature Sender
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Oil Pressure Sender
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Instrument Panel Group
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Junction Box
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Control Relay
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Magnetic Starter Switch Assembly
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Circuit Breaker
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Sensors Low Coolant Level
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Alternator
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Regulator
SUPPLEMENT FOR 3116 & 3126 MARINE ENGINE Electric Starting Motor
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.