Usage:
6V0890 (24V), 6V0885 (24V), 6V0927 (24V)
Rotation as viewed from drive end ... Clockwise
No load conditions at 25°C (77°F):
Speed ... 6950 ± 1650 rpm
Current draw ... 115 ± 25A
Voltage ... 23V
Clearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)
(1) Torque for large terminal nuts ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Torque for small terminal nuts ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(3) Torque for screws holding nose housing to lever housing ... 20.3 ± 2.7 N·m (15 ± 2 lb ft)
Solenoid
Current consumption (draw) at 25°C (77°F):
Pull in windings at 20V ... 49.3 ± 3.3A
Hold in windings at 20V ... 6.8A maximum
6V0501 (32V), 6V0508 (32V)
Rotation as viewed from drive end ... Clockwise
No load conditions at 25°C (77°F):
Speed ... 6500 ± 1000 rpm
Current draw ... 87.5 ± 12.5A
Voltage ... 30V
Clearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)
(1) Torque for large terminal nuts ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Torque for small terminal nuts ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(3) Torque for screws holding nose housing to lever housing ... 20.3 ± 2.7 N·m (15 ± 2 lb ft)
Solenoid
Current consumption (draw) at 25°C (77°F):
Pull in windings at 32V ... 41 ± 3.3A
Hold in windings at 32V ... 6.3A maximum
8C3449 (24V)
Rotation as viewed from drive end ... Clockwise
No load conditions at 25°C (77°F):
Speed ... 7643 ± 1683 rpm
Current draw ... 67.5 ± 7.5A
Voltage ... 23V
Clearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)
(1) Torque for large terminal nuts ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Torque for small terminal nuts ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(3) Torque for motor frame terminal ... 8 ± 3 N·m (70 ± 26 lb in)
Solenoid
Current consumption (draw) at 25°C (77°F):
Pull in windings at 20V ... 56.5 ± 4.5A
Hold in windings at 20V ... 14.6A
7T0795 (24V)
Rotation as viewed from drive end ... Clockwise
No load conditions at 25°C (77°F):
Speed ... 5500 rpm minimum
Current draw ... 140A maximum
Voltage ... 24V
(1) Torque for large terminal nuts ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Torque for small terminal nuts ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
Solenoid
Current consumption (draw) at 25°C (77°F):
Pull in windings at 24V ... 51A
Hold in windings at 24V ... 7A
Air
4W5105, 4W5106
(1) Cover.
Tighten the bolts evenly in small increases until the torque is ... 80 N·m (60 lb ft)
(2) Torque for bolts ... 36 N·m (26 lb ft)
(3) Torque for bolt ... 78 N·m (55 lb ft)
(4) Torque for bolt that holds piston ... 110 N·m (80 lb ft)
(5) Rotor clamp nut.
Tighten nut until clearance between rear end plate and rotor is ... 0.03 to 0.08 mm (0.001 to 0.003 in)
Check clearance again after the bolt for the clamp nut is tightened.
(6) Torque for bolt that holds rotor ... 120 N·m (90 lb ft)
105-5080, 105-5081
(1) Tighten bolts in steps to a torque of ... 30 ± 5 N·m (22 ± 4 lb ft)
(2) Clearance between rotor and end plate ... 0.81 mm (.032 in)
(3) Tighten bolts in steps to a torque of ... 11.3 N·m (8 lb ft)
Pressure Regulating Valve
Typical Example
(1) Adjusting screw.
(2) Inlet pressure ... 1725 kPa (250 psi)
Maximum permissible inlet pressure ... 3100 kPa (450 psi)
(3) Minimum outlet pressure ... 620 kPa (90 psi)
Maximum outlet pressure ... 1030 kPa (110 psi)