Automatic Lubrication - Install
Parts and Specification Information
Show/hide table
Illustration 1 | g03852564 |
Note: The lubrication lines for the top of the hoist cylinder may not be installed until the body has been installed onto the machine.
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
Show/hide table
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information. |
Show/hide table
Item | Part Number | Description | Qty | Specification | Approximate Weight |
1 | 6D-3479 | Clip | 4 | ||
2 | 8T-4896 | Hard Washer | 4 | ||
3 | 6V-8801 | Nut | 12 | ||
4 | 431-7913 | Strap | 8 | ||
5 | 7X-0296 | Bolt | 8 | ||
6 | 7C-4354 | Clip | 4 |
- Connect the autolube fast fill 442-3512 Hose As (A) to the "Grease Fill R5" connection.
- Connect the autolube supply 442-3511 Hose As (B) to the "Grease Supply R4" connection.
Show/hide table
Illustration 4 g03853153 An underside view of the front axle auto lubrication connection - Connect the front axle autolube supply 454-9842 Hose As (C) to the front axle autolube 352-6495 Tee As (D).
Show/hide table
Illustration 5 g03853309 A view of the right side front axle auto lubrication connections - Connect 442-3501 Hose As (E) to the top of the suspension cylinder. Secure hose assembly (E) in two places using one clip (1), one hard washer (2), and one nut (3) at each location.
- Connect 442-3503 Hose As (F) to the frame end of the rod.
- Connect 450-1713 Hose As (G) to the bottom of the suspension cylinder.
- Connect 451-1789 Hose As (H) to the front axle end of the upper linkage.
- Connect 442-3502 Hose As (J) to the front axle end of the lower linkage.
- Secure hose assembly (L) and hose assembly (K) to the upper linkage using four straps (4), four bolts (5), two clips (6) and four nuts (3).
- Connect 450-1710 Hose As (L) to the frame end of the upper linkage.
- Connect 450-1711 Hose As (K) to the frame end of the lower linkage.
- Repeat Steps 4, and 6 through 11 for the left side of the machine.
Show/hide table
Illustration 6 g03858416 A view of the rear axle auto lubrication connection - Connect 442-3498 Hose As (M) to the rear axle lubrication valve.
Show/hide table
Illustration 7 g03858858 A view of the rear axle and auto lubrication lines - Connect 442-3516 Hose As (N) to the rear axle connection pin.
- Connect 442-3516 Hose As (N) to the rear axle connection sleeve.
- Connect 442-3515 Hose As (P) to the bottom of the left hoist cylinder.
- Connect 442-3524 Hose As (R) to the bottom of the right hoist cylinder.
Show/hide table
Illustration 8 g03858926 A view of the rear axle and auto lubrication lines - Connect 442-3520 Hose As (S) to the top of the right suspension cylinder.
- Connect 442-3522 Hose As (T) to the right body pivot sleeve.
- Connect 442-3521 Hose As (U) to the top of the left suspension cylinder.
- Connect 442-3523 Hose As (V) to the left body pivot sleeve.
- Connect 442-3528 Hose As (W) to the 443-8873 Rod As.
Show/hide table
Illustration 2 | g03852739 |
A view of the platform auto lubrication connection |
Show/hide table
Illustration 3 | g03852840 |
A close up view of the platform auto lubrication connection |
Caterpillar Information System:
C8.7 Marine Engine Pistons and Connecting Rods - Remove and Install
G3516 Petroleum Engine Sensors and Electrical Components
C175-16 Locomotive Engine DEF Pump Power Supply - Test
C175-16 Locomotive Engine DEF Pump Motor - Test
2015/08/14 A Connector with a New Cap Is Now Used on the Engine Interface Box for Certain G3500B Engines {1408, 4460, 7426}
New Alternator Mounting Group Installation On Certain Electric Power Generation Engines{1405} New Alternator Mounting Group Installation On Certain Electric Power Generation Engines{1405}
New Turbocharger Heat Shields Are Used on Certain 3500 Marine and Petroleum Engines {1073} New Turbocharger Heat Shields Are Used on Certain 3500 Marine and Petroleum Engines {1073}
2015/07/07 New Thermowell Adapters Are Available for Certain 3500 Tier 2 Marine Engines {1906, 1929, 7498}
2015/06/26 Improved Heavy Duty Tier 3 and Tier 4 Injectors Are Now Used on Certain Engines {1251, 1254, 1290, 1713}
120 and 120 AWD Motor Grader Articulation Bearings - Lubricate
120 and 120 AWD Motor Grader Steering Frame Lock
120 and 120 AWD Motor Grader Before Starting Engine
120 and 120 AWD Motor Grader Cooling System Coolant Sample (Level 1) - Obtain
3512C Generator Set Engine Vibration Damper - Remove and Install
120 and 120 AWD Motor Grader Crankshaft Vibration Damper - Inspect
120 and 120 AWD Motor Grader Engine Air Filter Element - Clean/Replace
G3516 Petroleum Engine Product Lifting
G3516 Petroleum Engine Before Starting Engine
G3516 Petroleum Engine Refill Capacities
G3516 Petroleum Engine Starting Motor - Inspect
2015/07/17 A New Wiring Harness is Now Used on Certain C18 Marine Propulsion Engines {1408, 1921}
120 and 120 AWD Motor Grader Fuel System Filter - Replace
120 and 120 AWD Motor Grader Fuel Tank Water and Sediment - Drain
120 and 120 AWD Motor Grader Hydraulic System Oil - Change