Alternator - Assemble - M1 Series Alternator (35 Amp)
Assembly Procedure
Note: Before assembly, clean all parts in cleaning fluid. Allow the parts to air dry. DO NOT dry the parts with wiping cloths or with rags. Cloths and rags contain lint. Inspect all parts. Replace worn parts and replace damaged parts.
- Put field winding (24) into the rear frame. Install three bolts.
Show/hide table
Illustration 1 | g00825771 |
- Install "R" terminal (19). Put rectifier (23) into the rear frame. Install the four bolts. Tighten the "B+" terminal nut to the following torque: 29 ± 8 N·m (21 ± 6 lb ft) Tighten the "B-" terminal nut to the following torque: 4.4 ± 1 N·m (39 ± 9 lb in)
Show/hide table
Illustration 2 | g00825773 |
- Put rear frame (4) on stator (5). Align the marks on the stator and on the rear frame. Connect the stator leads to the rectifier.
Show/hide table
Illustration 3 | g00825774 |
- Install regulator (15) and capacitor (17). Install the two bolts.
Show/hide table
Illustration 4 | g00825775 |
- Connect the field winding leads and connect the wire (14) to the regulator and to the capacitor. Connect the other end of the wire (14) and connect wire (16) to the rectifier.
- Install the rear cover.
- Install two ball bearings (6) on the rotor. Install plate assembly (10), the rear spacer, the rear felt washer, plate (7), ball bearing (8), washer (11), front felt washer (12), and spacer (9) .
Show/hide table
Illustration 5 | g00825750 |
- Put rotor (26) into the front frame. Install the four bolts.
Show/hide table
Illustration 6 | g00825777 |
- The rotor remains connected to the front frame. The stator remains connected to the rear frame. Put front frame (3) into the rear frame (4). Align the marks on the front frame and on the rear frame. Install the four bolts.
Show/hide table
Illustration 7 | g00825778 |
- Install the fan, the key, the pulley, the washer, and the pulley nut. Tighten the pulley nut to the following torque: 102 ± 7 N·m (75 ± 5 lb ft)
- Restore the residual magnetism in the alternator. Refer to Testing and Adjusting, "Residual Magnetism - Restore".
End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Caterpillar Information System:
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
2001/08/13 An Improved Throttle Control Group is Available {1265, 1276, 1913}
216, 226, 232 and 242 Skid Steer Loaders Machine Systems Work Tool Hydraulic System
793B Off-Highway Truck Air System and Brakes Brake Cooling System
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0689 - FMI 03
2001/08/13 New Tooling Is Recommended For The Disassembly And The Assembly Of The Planetary Drive Group {4050}
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0590 - FMI 12
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Using Caterpillar Monitoring System to Determine Diagnostic Codes
3500B Engines Crankcase Pressure
216, 226, 232 and 242 Skid Steer Loaders Machine Systems Gear Motor (Fan)
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0590 - FMI 09
2001/08/06 Correct Sealant Must Be Used When Bulkhead Fittings for the Air Conditioner are Installed to the Cab {7320}
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0689 - FMI 05
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System MID 027 - CID 1236 - FMI 06
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0689 - FMI 06
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0690 - FMI 03
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0690 - FMI 05
554 Forwarder and 574 Forwarder Hydraulic System Lift Cylinder
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System MID 116 - CID 0690 - FMI 06
CP-663E, CS-663E and CS-683E Vibratory Compactors Machine Systems Hood Tilt Actuator - Remove and Install
TH210 and TH215 Telehandlers Fuel Tank Cap - Clean
740 EJECTOR Articulated Truck Ejector Cylinder Bearing - Lubricate
740 and 740 EJECTOR Articulated Trucks Power Train Speed Sensor (Transmission) - Remove and Install
740 EJECTOR Articulated Truck Ejector Cylinder Pivot - Lubricate