Torques for Metric Fasteners
Show/hide table
NOTICE |
---|
Be very careful never to mix metric with U.S. customary (standard) fasteners. Mismatched or incorrect fasteners causes machine damage or malfunction and can result in personal injury. Original fasteners removed from the machine should be saved for reassembly whenever possible. If new fasteners are needed, they must be of the same size and grade as the ones that are being replaced. The material strength identification is usually shown on the bolt head by numbers 8.8, 10.9, etc. The following charts give general torques for Metric bolts, nuts and taperlock studs of Grade 8.8. |
Note: Metric hardware must be replaced with metric hardware. Check the parts manual for proper replacement.
Torques for Bolts and Nuts
Show/hide table
TORQUES FOR BOLTS AND FOR NUTS     | ||
---|---|---|
METRIC ISO (1) THREAD     | ||
Thread Size     | Standard Torque     | |
Metric     | N·m (2)     | lb ft     |
M6     | 12 ± 3     | 9 ± 2     |
M8     | 28 ± 7     | 20 ± 5     |
M10     | 55 ± 10     | 40 ± 7     |
M12     | 100 ± 20     | 75 ± 15     |
M14     | 160 ± 30     | 120 ± 22     |
M16     | 240 ± 40     | 175 ± 30     |
M20     | 460 ± 60     | 340 ± 45     |
M24     | 800 ± 100     | 600 ± 75     |
M30     | 1600 ± 200     | 1200 ± 150     |
M36     | 2700 ± 300     | 2000 ± 225     |
Show/hide table
( 1 ) | International Standards Organization (ISO) |
( 2 ) | 1 Newton meter (N·m) is approximately 0.1 mkg. |
Torques for Taperlock Studs
Show/hide table
TORQUES FOR TAPERLOCK STUDS     | ||
---|---|---|
METRIC ISO (1) THREAD     | ||
Thread Size     | Torque for Standard Taperlock Stud     | |
Metric     | N·m (2)     | lb ft     |
M6     | 8 ± 3     | 6 ± 2     |
M8     | 17 ± 5     | 13 ± 4     |
M10     | 35 ± 5     | 26 ± 4     |
M12     | 65 ± 10     | 48 ± 7     |
M16     | 110 ± 20     | 80 ± 15     |
M20     | 170 ± 30     | 125 ± 22     |
M24     | 400 ± 60     | 300 ± 45     |
M30     | 750 ± 80     | 550 ± 60     |
M36     | 1200 ± 150     | 890 ± 110     |
Show/hide table
( 1 ) | International Standards Organization (ISO) |
( 2 ) | 1 Newton meter (N·m) is approximately 0.1 mkg. |
Caterpillar Information System:
938G Wheel Loader and IT38G Integrated Toolcarrier Bucket Wear Plates - Inspect/Replace
446B Backhoe Loader Torques for Standard Worm Drive Band Hose Clamps
120H and 135H Motor Graders Air System and Brakes Service Brakes
561M Pipelayer Radiator Core - Clean
561M Pipelayer Radiator Pressure Cap - Clean/Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Hydraulic System Oil Level - Check
120H and 135H Motor Graders Air System and Brakes Service Brake Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Circuit Breakers - Reset
IT14G Integrated Toolcarrier Roading the Machine
928G Wheel Loader Shipping the Machine
120H and 135H Motor Graders Air System and Brakes Air Control Valve (Parking Brake)
120H and 135H Motor Graders Air System and Brakes Parking Brake
584 and 584HD Forwarders Tire Inflation Pressure Adjustment
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Window Wiper - Inspect/Replace
928G Wheel Loader Steering Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Window Washer Reservoir - Fill
IT62G Series II Integrated Toolcarrier Tire Inflation - Check
120H and 135H Motor Graders Air System and Brakes Service Brakes
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Transmission Oil Level - Check
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Transmission Oil Filter - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Hydraulic System Oil Filter - Replace
793B Off-Highway Truck Steering System Accumulator Charging Valve
793B Off-Highway Truck Steering System Steering Gear
966G and 972G Wheel Loaders Hydraulic System Oil - Change