Cold Weather Starting
Show/hide table
不要使用乙醚(起动液),除非明确说明可以这样做。 如果发动机配备了空气进气加热器(电热式或燃油点燃式歧管加热器),任何时候都不要使用乙醚(起动液)。 使用乙醚可能导致发动机损坏或人身伤害。 |
使用缸体冷却液加热器或其它加热曲轴箱油的方法会改善温度低于
注: 如果发动机已经有几个星期没有运行,则燃油可能已经排出。 空气可能会进入滤清器壳体。 此外,在更换燃油滤清器后,滤清器壳体中会留有部分空气。 有关燃油系统充注的更多信息,请参阅操作和保养手册, "燃油系统 - 充注"(保养部分)。
Show/hide table
注意 |
---|
当飞轮正在转动时,不要合上起动马达。 不要带负载起动发动机。 如果发动机没有在30秒内起动,松开起动开关或起动按钮并等待2分钟,在再次起动发动机以前,让起动马达先冷却下来。 |
- 确保快速断路开关处于接通位置。
- 按下起动按钮以转动发动机。
转动发动机时,不要下推油门或一直踩下油门。 系统将自动提供起动发动机所需的正确燃油量。
- 如果发动机在 30 秒内未能起动,松开点火按钮或点火开关。 等待 2 分钟,以便在再次试图起动发动机之前让起动马达冷却。
Show/hide table
注意 机油压力应该在发动机起动后15秒内升上来。 直到机油压力表指示正常后再提高发动机转速。 如果机油压力在15秒钟内在表中无指示,不要运转发动机。 使发动机停机,调查并纠正原因。
- 让发动机怠速运转约 3 分钟。 怠速运转发动机,直到水温表读数开始升高。 在暖机期间,检查所有仪表。
注: 仪表板上机油压力和燃油压力的读数显示应处在正常范围。 在机油压力表指示最低正常压力以前,不要向发动机加负载或提高发动机转速。 检查发动机有无泄漏和/或异常噪音。
注: 对于低环境温度,难以起动或白烟过多 - 发动机在低怠速下运转可快速预热。
Caterpillar Information System:
C27 and C32 Generator Set Configuration Parameters
C27 and C32 Generator Set Product Description
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuel Tank Water and Sediment - Drain
C27 and C32 Generator Set Maintenance Interval Schedule - Prime
C27 and C32 Generator Set Maintenance Interval Schedule - Standby
794 AC Off-Highway Truck Leaving the Machine
C11 and C13 Industrial Engines Maintenance Interval Schedule - Engines Which Have Shallow Oil Pans
Installing the New NOx Reduction System Pressure Sensor Kit on Certain C7.1 Engines {1718, 1917, 1923, 1924, 7400} Installing the New NOx Reduction System Pressure Sensor Kit on Certain C7.1 Engines {1718, 1917, 1923, 1924, 7400}
New NOx Reduction System (NRS) Differential Pressure Sensor Kit on Certain C7.1 Engines {1718, 1917, 1923, 1924, 7400} New NOx Reduction System (NRS) Differential Pressure Sensor Kit on Certain C7.1 Engines {1718, 1917, 1923, 1924, 7400}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuel System Water Separator - Drain
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuel System Primary Filter (Water Separator) Element - Replace
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Final Drive Oil Sample - Obtain
C27 and C32 Generator Set Starting the Engine
C27 and C32 Generator Set Control Panel - Inspect/Test
C27 and C32 Generator Set Model View Illustrations
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Fuses - Replace
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Oil Pan - Remove and Install
C7.1 Marine Propulsion Engine Rocker Arm and Shaft - Remove
C7.1 Marine Propulsion Engine Rocker Arm - Disassemble
C7.1 Marine Propulsion Engine Rocker Arm - Assemble
C7.1 Marine Propulsion Engine Rocker Arm and Shaft - Install
336, 336 GC and 340 Excavator Systems Main Hydraulic Pump
336, 336 GC and 340 Excavator Systems Diagnostic Trouble Codes
The Flange Head on 442-5593 Coupling As May Have Been Manufactured Incorrectly {5057} The Flange Head on 442-5593 Coupling As May Have Been Manufactured Incorrectly {5057}