Fuel Control Valve - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Turn OFF the gas supply.
Show/hide table
Illustration 1 g06008699 - Disconnect the harness assembly from fuel control valve (2).
- Remove bolts (1) and bolts (3).
- Attach a suitable lifting device to fuel control valve (2). The weight of fuel control valve (2) is approximately
68 kg (150 lb) . - Remove bolts (4) and fuel control valve (2). Remove the gaskets from the tube assemblies.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. Turn the disconnect switch OFF when draining and/or removing any fuel system components. |
- Attach a suitable lifting device to fuel control valve (2). The weight of fuel control valve (2) is approximately
68 kg (150 lb) . - Install the gaskets on the tube assemblies. Place fuel control valve (2) in position and install bolts (4).
- Install bolts (1) and bolts (3). Tighten the bolts to a torque of
115 ± 20 N·m (85 ± 15 lb ft) . - Connect the harness assembly to fuel control valve (2).
- Turn ON the gas supply.
Show/hide table
Illustration 2 | g06008699 |
Caterpillar Information System:
G3516 TA Engine Engine Sensors
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000} Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
Caterpillar Machine Fluids Recommendations Warranty Information
795F AC and 795F AC XQ Off-Highway Trucks Hood Tilt
Check for the Correct Bolt Torque for the Air Shutoff Butterfly Plate on Certain 3500 Engines {1078} Check for the Correct Bolt Torque for the Air Shutoff Butterfly Plate on Certain 3500 Engines {1078}
New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900} New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900}
New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920} New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920}
G3516 TA Engine Engine Governing
G3516 TA Engine Electronic Control System Operation
New Scraper Mounting for Certain Asphalt Compactors {6607} New Scraper Mounting for Certain Asphalt Compactors {6607}
G3516 TA Engine Ignition System
Caterpillar Machine Fluids Recommendations Reference Material
G3516 TA Engine Gas Pressure Regulator
G3516 TA Engine Air Inlet and Exhaust System Components
G3516 TA Engine Aftercooler
G3516 TA Engine Turbocharger
G3516 TA Engine Exhaust Bypass Valve
G3516 TA Engine Valve System Components
G3516 TA Engine Lubrication System
G3516 TA Engine Accumulator
G3516 TA Engine Cooling System
G3516 TA Engine Camshaft