NRS Exhaust Gas Temperature Is High
Use this procedure to troubleshoot a high NOx Reduction System (NRS) exhaust gas temperature. Also, use this procedure if one of the following event codes is active or logged.
Show/hide table
J1939 Code and Description | CDL Code and Description | Comments |
---|---|---|
412-15
Engine Exhaust Gas Recirculation Temperature : High - least severe (1) |
E1092 (1)
High EGR Temperature |
The temperature of the NOx Reduction System (NRS) exhaust gas has exceeded the threshold for a set amount of time. |
412-16
Engine Exhaust Gas Recirculation Temperature : High - moderate severity (2) |
E1092 (2)
High EGR Temperature |
The temperature of the NRS exhaust gas has exceeded the threshold for a set amount of time. |
Show/hide table
Associated Codes | ||
J1939 Code | CDL Code | Troubleshooting Procedure |
110-0 | E361 (3) | Troubleshooting, "Coolant Temperature Is High" |
110-15 | E361 (1) | Troubleshooting, "Coolant Temperature Is High" |
110-16 | E361 (2) | Troubleshooting, "Coolant Temperature Is High" |
- Codes
- NRS coolers
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Check for Codes A. Connect Cat® Electronic Technician (ET) to the service tool connector. B. Look for active codes that are associated with the system for the event code. |
Codes |
Result: An associated code is active. Repair: Troubleshoot any associated codes before continuing with this test. Result: A code is active or logged. Proceed to Test Step 2. |
2. Perform a "EGR System Test" A. Connect Cat ET. B. Use Cat ET to perform the following diagnostic test: - "EGR System Test" |
Test |
Result: The "EGR System Test" did not complete due to a E1092 or 412 code. Repair: Perform the following procedure: 1. Repair or replace the vent line from the coolers to the engine block. Remove the exhaust lines from the inlet and the outlet of the coolers. Inspect the internal passage of each cooler for coolant. If coolant is found, replace the coolers. 2. Connect Cat ET. 3. Use Cat ET to perform the following diagnostic test: - "EGR System Test" Verify that the repair eliminated the problem. Return to service. Result: The test failed and reported a Cat ET service error identifier. Repair: Refer to Troubleshooting, "NOx Reduction System (NRS) - Test" for additional information. Result: The test was successfully. Proceed to Test Step 3. |
3. Check for leaks in the NOx Reduction System (NRS) Coolers A. Remove the NRS coolers. Refer to Disassembly and Assembly for additional information. B. Perform a leak test on each cooler. Refer to System Operation Testing and Adjusting, "Exhaust Cooler (NRS) - Test" for additional information. |
Leaks |
Result: The cooler has internal leakage. Repair: Perform the following procedure: 1. Replace the cooler. Replace the connection for the bellows at the inlet of the cooler. 2. Connect Cat ET. 3. Use Cat ET to perform the following diagnostic test: - "EGR System Test" Verify that the repair eliminated the problem. Return to service. Result: The cooler did not have internal leakage. Repair: Clean the cooler. Refer to Testing and Adjusting, "Exhaust Cooler (NRS) - Clean" for additional information. Return to service. |
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Caterpillar Information System:
C13 Industrial Engine Water in Fuel - Test
C13 Industrial Engine Variable Valve Actuator Response - Test
C13 Industrial Engine Variable Valve Actuator - Test
C175-16 Locomotive Engine NOx Sensor Supply - Test
C13 Industrial Engine Switch Circuits - Test
C13 Industrial Engine Speed/Timing - Test
C13 Industrial Engine Speed Control - Test
C13 Industrial Engine Solenoid Valve - Test
C13 Industrial Engine Shutdown (Ground Level) - Test
C13 Industrial Engine Sensor Supply - Test
C13 Industrial Engine Sensor Signal (Analog, Passive) - Test
C13 Industrial Engine Sensor Signal (Analog, Active) - Test
C280 Marine Engines NOx Sensor - Test
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900} Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Installation of Exhaust Shield Assemblies On Certain G3520C Engines {1059} Installation of Exhaust Shield Assemblies On Certain G3520C Engines {1059}
XQC1200 Power Module Setup
XQC1200 Power Module Coolant (ELC) - Change
C280 Marine Engines DEF Pump Power Supply - Test
2014/10/31 New Recommendations for Starters and Batteries Used on 3516 Engines Operating in China {1401, 1453}
2014/11/26 A New Valve Cover Base Is Used on Certain C15 and C18 Commercial Engines {1120}
XQC1200 Power Module Coolant (DEAC) - Change
XGC1900 Generator Sets Circuit Breakers - Reset
C280 Marine Engines DEF Pump Motor - Test
C27 and C32 Engine for MD6250 and MD6310 Drill Timing - Calibrate