Fuel Injection Pump
Show/hide table
| |
| Illustration 1 | g03395174 |
Show/hide table
| Specification for 359-2806 Fuel Injection Pump Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 241-6157 Plug | Torque to |
| 2 | 4 | 3T-0849 Bolt | Use the following procedure in order to tighten the bolts: Refer Illustration 1 for bolt tightening sequence. 1. Tighten the bolts in the numerical sequence to 2. Again, tighten the bolts in the numerical sequence to 3. Ensure that all bolts are torqued to |
| 3 | 12 | 177-1809 Bolt | Use the following procedure in order to tighten the bolts: Refer Illustration 1 for bolt tightening sequence. 1. Tighten the bolts in the numerical sequence to 2. Again, tighten the bolts in the numerical sequence to 3. Again retighten the bolts in a numerical sequence to 4. Ensure that all bolts are torqued to |
| 4 | 4 | 8T-4178 Bolt | Use the following procedure in order to tighten the bolts: Refer Illustration 1 for bolt tightening sequence. 1. Tighten the bolts in the numerical sequence to 2. Again, tighten the bolts in the numerical sequence to 3. Again retighten the bolts in a numerical sequence to 4. Ensure that all bolts are torqued to |
Caterpillar Information System:
3516C Petroleum Engines Engine Oil Cooler - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
374F Excavator Monitoring System
3500 Generator Sets Product Description
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
794 AC Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
794 AC Off-Highway Truck Window Wiper - Inspect/Replace
794 AC Off-Highway Truck Windows - Clean
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install - Remote Mounted
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install - With Remote Mounted Oil Filter Base
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Power Take Off equipped
2013/06/18 Proper Pinout Locations on Certain Atlas Copco Industrial 3512C Engines {1408}
C4.4 Industrial Engine Safety Messages
3512C Oil Well Service Engines Starting the Engine
2013/06/20 Additional Support for the Bucket Circuit Tube Assembly is Available for Certain Excavators and Mobile Hydraulic Power Units {5057}
2013/06/26 A New Precooler Hose Is Now Used on Certain C18 Tier 4 Interim Industrial Engines {105P, 7554}
2013/09/16 Special Instructions Are Available for Retrofitting the Dynamic Gas Blending Kits on Certain 3512C Petroleum Engines {1250, 1280}