Engine Oil Lines
Show/hide table
图 1 | g03326732 |
Show/hide table
图 2 | g03328981 |
A 区视图 |
Show/hide table
381-7039 发动机机油管路总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 2     | 7N-7697 柱塞     | 冷却喷嘴顺序阀: 阀必须在压差为 130 ± 30 kPa (19 ± 4 psi) 时开始开启。 阀必须在 200 ± 30 kPa (29 ± 4 psi) 时完全开启。     |
2     | 2     | 6B-9202 弹簧     | 在试验力下的长度为 68.27 mm (2.688 in)。     |
试验力为 85 - 100 N19 (.0 - 22.4 lb)。 |
|||
试验后的自由长度为 112.72 mm (4.438 in)。 |
|||
3     | 2     | 0S-1571 螺栓     | 按以下顺序拧紧夹紧螺栓: 将卡箍组件紧固到管上。 将卡箍组件拧紧到弯管上。 将卡箍组件拧紧到管上。     |
4     | 2     | 0S-1594 螺栓     | |
5     | 1     | 2W-1053 塞     | 拧紧至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。     |
6     | 1     | 2W-1969 旁通阀     | 机油冷却器旁通阀必须在压差为 180 ± 20 kPa (26 ± 3 psi) 时开启。     |
7     | 1     | 2W-1635 弹簧     | 在试验力下的长度为 102.0 mm (4.02 in)。     |
试验力为 518 ± 26 N (116 ± 6 lb)。 |
|||
试验后的自由长度为 143.4 mm (5.65 in)。 |
Caterpillar Information System:
3500 Engines for Caterpillar Built Generator Sets Engine Oil Lines
3500B High Displacement Thermocouple
C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Test - If Equipped
C1.5 and C2.2 Engines for Caterpillar Built Machines Glow Plugs - Test
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Test
3500 Industrial Engines Engine Speed/Timing Sensor
3512B and 3512C Petroleum Generator Set Engines Exhaust Fitting
3500C Marine Engines Cover Group (Front Housing)
3512B and 3512C Petroleum Generator Set Engines Exhaust Elbow
3500C Marine Engines Cover (Vibration Damper Guard)
3512B and 3512C Petroleum Generator Set Engines Exhaust Elbow
3512B and 3512C Petroleum Generator Set Engines Generator Coupling
3500 Engines for Caterpillar Built Generator Sets Engine Oil Lines
3500C Marine Engines Engine Oil Lines
3516B Engine Engine Oil Pan (Front) - Remove and Install
3516B Engine Engine Oil Pan (Rear) - Remove and Install
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Sensor Calibration Required - Test
TA2 Technical Inspection for Certain 3512B and 3512C Petroleum Engines{1000} TA2 Technical Inspection for Certain 3512B and 3512C Petroleum Engines{1000}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Switch Circuits - Test
390F Excavator Specifications
2012/11/30 New Taperlock Studs for Certain G3406, G3408 , and G3412 Engines {1057, 7553}
3508B Industrial Engines Air Starting Motor Pressure Regulating Valve
3512B and 3512C Petroleum Generator Set Engines Engine Oil Lines
3500 Industrial Engines Air Starting Motor