Cylinder Head
Show/hide table
Illustration 1 | g03132457 |
Show/hide table
Specification for 4P-6569 Cylinder Head Gp | |||
Item | Qty | Part | Specification Description |
1 | 1 | 5B-7890 Pipe Plug | Before assembly, apply Loctite C5A copper anti-seize to the threads. |
2 | 6 | 131-0420 Cylinder Head Fastener Gp | Before assembly, apply engine oil to cylinder head bolt threads.
Use the following procedure in order to tighten the cylinder head bolts. Refer to Illustration1 for the tightening sequence: 1. Tighten bolt 1 through bolt 8in the numerical sequence to 2. Again tighten bolt 1 through bolt 8 in the numerical sequence to 3. Again tighten bolt 1 through bolt 8 in the numerical sequence to 4. Tighten two bolts (4) only after bolt 1 through bolt 8 have been given the final torque. Tighten two bolts (4) to |
3 | 2 | 131-0421 Cylinder Head Fastener Gp | |
4 | 2 | 5B-0213 Bolt |
Show/hide table
Illustration 2 | g03132456 |
Show/hide table
Item | Qty | Part | Specification Description |
5 | 4 | 6I-1713 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature. |
6 | 5 | 3B-0645 Cup Plug | Apply high strength or high temperature anaerobic flange sealant to the bores for the cup plugs prior to the installation. |
7 | 3 | 3B-0623 Cup Plug | Apply high strength or high temperature anaerobic flange sealant to the bores for the cup plugs prior to the installation.
Installation depth (D) is |
B | 2 | 3B-0623 Cup Plug | Installation depth of the cup plugs from the top surface of the cylinder head is |
8 | 1 | 4P-6925 Oil Sleeve | During installation, shrunk the oil sleeve with reduced temperature.
Installation depth is |
Caterpillar Information System:
C32 Marine Engines Unit Injector Sleeve - Install
C32 Marine Engines Unit Injector Sleeve - Remove
793F Off-Highway Truck Engine Supplement Turbocharger - Remove and Install - High Altitude
C7.1 Industrial Engine Fuel Filter (In-Line) - Replace
G3500 Engines Cylinder Head
G3500 Engines Cylinder Head
C9.3 Tier 4 Final Engines Fuel Injection Pump
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Replace
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Configure
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Symptom Troubleshooting
2012/07/19 Improved Flame Arrestors Are Used for Certain G3500E Engines {1071, 1092}
CEM Locomotive Aftertreatment Catalyst (DOC) - Replace
C7.1 Industrial Engine Maintenance Interval Schedule
C9.3 Industrial Engine Turbocharger
C6.6 Industrial Engine Engine Crankcase Breather Element - Replace
C4.4 Industrial Engine Fuel System Primary Filter (Water Separator) Element - Replace
C4.4 Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C4.4 Industrial Engine Fuel System Secondary Filter - Replace
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C13, C15, and C18 Tier 4 Final Engines DEF Pressure Is High
C9 On-highway Engines ARD Combustion - Test
C7 and C9 On-Highway Engines Diesel Particulate Filter Collects Excessive Soot
C9 On-highway Engines ARD Failed to Ignite
C9 On-highway Engines ARD Temperature Is Low