Correct Orientation of the V-Band Clamp on the Center Housing/Turbine Housing Joint Is Needed on Certain C15 Truck Engines {1052, 1053}
- Engine:
- C15 (S/N: BXS1-UP; MXS1-UP; NXS1-UP)
Improper orientation of V-band clamp used on the center housing/turbine housing joint can lead to an improper clamping force. Also if the clamp is oriented incorrectly, access to the clamp nut with a socket or box end wrench will be difficult.
Show/hide table
Illustration 1 | g02730683 |
Show/hide table
Illustration 2 | g02730878 |
To be correctly oriented, the threaded rod of the V-band clamp should be positioned parallel to the turbine housing (A). The threaded rod of the V-band clamp should be positioned approximately 150 ± 5 degrees from the turbine housing inlet flange plane (B).
Caterpillar Information System:
C3.4B Engines Diesel Particulate Filter Active Regeneration Was Interrupted
Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562} Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562}
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electronic Control Unit - Flash Program
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
320 GC, 320 and 323 Excavator Machine Systems Specifications Refrigerant Compressor
3512C and 3516C Marine Auxiliary and Generator Set Engines Fumes Disposal Filter Element - Replace
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Transmission - Calibrate
3512C Petroleum Engines Data Link Configuration Status - Test
2011/10/10 A New Charging Alternator Group Is Used on C18 Engines In Certain Products {1405}
319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D} 319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D}
2011/12/15 A New Service Tool for Installing the Service Sleeve Bearings in Hydraulic Gear Pumps Is Now Available for Certain CAT Machines {0738, 5073, 5073, 7551}
Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426} Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426}
3500 Generator Sets Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Precleaner - Check/Clean
3516C Industrial Engine Product Lifting
2011/11/16 A New Turbocharger Water Line Is Used for Certain 3516B and 3516C Engines {1380}
2011/12/23 Special Instruction, REHS7409, "Initial Start-Up of CG137 and G3300B Engines" Is Available {1000}
3516C Marine Engine Engine Operation
2011/10/19 Improved Bolts and Washers Along with a New Procedure Are Used to Fasten the Pilot to the Lockup Clutch Housing {3101, 7553}
2011/12/14 A New Engine Oil Cooler Bypass Is Used for C175-16 Engines {1307}
320E and 323E Excavators Machine System Specifications Travel Motor Guard
320E and 323E Excavators Machine System Specifications Swivel
2011/11/11 New Heat Exchanger Groups and Spacers Are Used on Certain C32 Marine Engines {1379}