Engine Oil Pump - Disassemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-0510 | Driver Group | 1 |
B | 1P-2320 | Puller Assembly | 1 |
Start By:
- Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolt (5), thrust plate (6), and idler gear assembly (7) from shaft assembly (8).
- Use Tooling (A) and a suitable press in order to remove the bearing from idler gear assembly (7).
- Remove shaft assembly (8) from body (4). Remove bolt (1) and washer (2).
- Use Tooling (A) and Tooling (B) in order to remove drive gear (3) from body (4). Remove the key from the pump shaft.
Show/hide table
Illustration 2 g02352498 Show/hide tablePersonal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Remove bolts (18) and separate cover (17) from body (4).
- Use Tooling (A) and a suitable press in order to remove bearings (16) from cover (17).
- Remove shaft assemblies (15).
- Remove bolts (13) and retainer (12).
- Remove spring (11), plunger ring (10), and plunger (9).
- Use Tooling (A) and a suitable press in order to remove bearings (14) from body (4).
Show/hide table
Illustration 1 | g02352497 |
Caterpillar Information System:
CX28 On-Highway Transmission Breather (Transmission) - Clean
3512B and 3512C Petroleum Generator Set Engines Customer Specified Parameters Worksheet
CG137-08 and CG137-12 Industrial Engines System Configuration Parameters
3516B Marine Auxiliary Engine Configuration Parameters
C15 and C18 Engines Fuel System Secondary Filter - Replace
C27 and C32 Engines Engine Oil Cooler - Remove and Install
3516B Marine Auxiliary Engine Sensor Supply - Test
CG137-08 and CG137-12 Industrial Engines Spark Plug
3516B Marine Auxiliary Engine Secondary ECM - Test
3516B Marine Auxiliary Engine ECM/Personality Module - Test
C27 and C32 Tier 4 Engines Fan Adapter Fastener
2010/12/06 A Procedure Is Now Available to Adjust the Overload Protection on Certain Generator Sets. {4450, 4493}
C15 Petroleum Generator Set Alarms and Shutoffs
C27 Petroleum Engine Engine Oil Pump - Assemble
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
Enabling Either of Two Programmable Monitoring Parameters Causes a Loss of Communication for the Electronic Control Module (ECM) on C175-16 Generator Set Engines{1901, 1920} Enabling Either of Two Programmable Monitoring Parameters Causes a Loss of Communication for the Electronic Control Module (ECM) on C175-16 Generator Set Engines{1901, 1920}
C27 and C32 Engines Flywheel Housing - Remove and Install
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Required Tools
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Refrigerant Recovery
UPSB220 Uninterruptible Power Supply Display Messages
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Manifold Gauge Set (Refrigerant) - Install
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Refrigerant System - Evacuate
Conventional (Dry) Welding Procedure for Rollers and Idlers {0679, 4150, 4159, 4180, 7950} Conventional (Dry) Welding Procedure for Rollers and Idlers {0679, 4150, 4159, 4180, 7950}
C7.1 Industrial Engine Turbocharger - Install - First Stage Turbocharger