Gear Group (Rear) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Group | 1 |
Start By:
- Remove the flywheel housing.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- The engine must be put in time before the flywheel housing is removed. This is done in order to make sure that the rear gear group is in alignment with the rotation of the engine, as shown.
Show/hide table
Illustration 2 g02033554 - Remove bolts (1), plate (2), and gear assembly (3).
Show/hide table
Illustration 3 g02033555 - Use Tooling (A) and a suitable press to remove bearing (4) from gear assembly (3). Use Tooling (A) and a suitable press to separate gear assembly (3).
Show/hide table
Illustration 4 g02033556 - Remove bolts (6), bolts (7), and camshaft idler gears (5).
Show/hide table
Illustration 5 g02033557 - Remove shafts (8) and the thrust washers from camshaft idler gears (5).
- Use Tooling (A) and a suitable press to remove the bearings from camshaft idler gears (5).
Show/hide table
Illustration 6 g02033558 - Remove bolts (9) and shaft (10).
- Remove bolts (12) and crankshaft gear (11).
Note: The following Step is for a 3508 Engine.
Show/hide table
Illustration 1 | g01056631 |
- Install camshaft idler gears (5) and gear assembly (3) in the reverse order of removal.
- Tighten bolts (9) to a torque of
140 ± 10 N·m (105 ± 7 lb ft) . - Tighten bolts (6) and bolts (7) to a torque of
240 ± 20 N·m (175 ± 15 lb ft) . - The bore in the bearings in camshaft idler gears (5) should be
81.060 ± 0.010 mm (3.1913 ± 0.0004 inch) after installation. The bearings should be installed to a depth of1.00 ± 0.25 mm (0.039 ± 0.010 inch) . - The bore in the bearing in gear assembly (3) should be
75.060 ± 0.010 mm (2.9551 ± 0.0004 inch) after installation. The bearings should be installed to a depth of1.5 ± 0.5 mm (0.06 ± 0.02 inch) . - Apply clean engine oil to the bearings prior to assembly.
- Raise the temperature of the larger gear in order to assemble gear assembly (3).
- Tighten bolts (9) to a torque of
Caterpillar Information System:
2009/12/03 Gasket for the Water Pump on 3054C, 3054E, C4.4 and C6.6 Engines {1361, 1395, 7555}
Hydraulic Excavator Idler Disassembly and Assembly Procedures {0729, 4159} Hydraulic Excavator Idler Disassembly and Assembly Procedures {0729, 4159}
G3500B Engines Engine Governing - Adjust
3508, 3512 and 3516 Generator Set Engines Balancer Group (Front) - Remove and Install - 3508 Engine
C13 Industrial Engines Engine Oil Pan
C13 Industrial Engines Engine Oil Pan
C13 Industrial Engines Engine Oil Pan
C18 Marine Engine Maintenance Interval Schedule
C32 Auxiliary Engine Emergency Stopping
3508, 3512 and 3516 Generator Set Engines Connecting Rod Bearings - Remove and Install
3508, 3512 and 3516 Generator Set Engines Cylinder Head - Assemble
C175-16 PETROLEUM ENGINES Flywheel - Remove and Install
120M, 12M, 140M and 160M Motor Graders Machine Systems Position Sensor (Articulation)
CG137-08 and CG137-12 Industrial Engines Gas Pressure Regulator
UPSB130 Uninterruptible Power Supply Regulatory Compliance
C13, C15, and C18 Engines for Caterpillar Built Machines Cooling Fan - Calibrate
UPSB130 Uninterruptible Power Supply General Hazard Information
UPSB130 Uninterruptible Power Supply Product Identification
UPSB130 Uninterruptible Power Supply General Information
UPSB130 Uninterruptible Power Supply Component Description
UPSB130 Uninterruptible Power Supply Electrical Specification
UPSB130 Uninterruptible Power Supply Product Location
UPSB130 Uninterruptible Power Supply Single UPS Connection
UPSB130 Uninterruptible Power Supply Parallel UPS Connection