Flywheel - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺栓 M24 X 2 X 200 mm |
2 |
B | 138-7575 | 连杆支架 | 3 |
C | 189-0408 | 钩环组件 | 1 |
D | 1U-9200 | 操纵杆滚轮举倾机构 | 1 |
- 将两个螺栓 (3) 从连接器 (2) 上拆下。 安装工具 (A)。
- 安装工具 (B)。 连接器 (2) 的重量约为
96 kg (212 lb) 。 拆下剩余的螺栓 (3)。 拆下螺栓 (1 )。 在工具 (A) 上滑动连接器 (2)。 拆下连接器 (2)。Show/hide table图 2 g02032713 Show/hide table图 3 g02032733 - 将两个螺栓 (4) 从飞轮 (5) 上拆下。 安装工具 (A)。
Show/hide table
图 4 g02032754 - 安装工具 (B)、工具 (C) 和工具 (D) 以支撑飞轮 (5) 的重量。 飞轮 (5) 的重量约为
177 kg (390 lb) 。 拆下剩余的螺栓 (4)。 拆下隔套 (6)。 在工具 (A) 上滑动飞轮 (5)。 拆下飞轮 (5)。
Show/hide table
图 1 | g02032640 |
- 按与拆卸相反的顺序安装飞轮 (5)。
- 检查齿圈的状况。 如有必要,采用以下步骤更换齿圈。
- 从飞轮上拆卸损坏的齿圈。
- 加热新齿圈。
- 将齿圈安装在飞轮上。 确保齿轮轮齿的斜面对着起动马达的小齿轮。
- 拧紧新螺栓 (4) 至扭矩为
550 ± 50 N·m (406 ± 37 lb ft) 。 将螺栓 (4) 继续拧紧 85 至 95 度。 - 拧紧新螺栓 (3) 至扭矩为
350 ± 40 N·m (258 ± 30 lb ft) 。
Caterpillar Information System:
3508, 3512 and 3516 Generator Set Engines Cylinder Head - Disassemble
2010/01/13 New Flame Detection Temperature Sensors Are Available for Certain C13 and C15 On-Highway Engines {108B, 108E, 108M}
2009/12/01 A New Heat Shield Is Available for Some C18 Engines {1067}
C13, C15, and C18 Tier 4 Interim Engines Shutdown (Ground Level) - Test
349F and 352F Excavators Air Conditioning and Heating Control
C7.1 Industrial Engine and Generator Set Diesel Particulate Filter Temperature Is High
793F Off-Highway Truck Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
349F and 352F Excavators Seat
793F Off-Highway Truck Engine Supplement Piston Motor (Fan Drive) - Assemble
793F Off-Highway Truck Engine Supplement Piston Motor (Fan Drive) - Disassemble
349F and 352F Excavators Fire Extinguisher Location
2009/12/03 Processes Eliminate High Fuel Pressure Event Codes in the Low Pressure Fuel Systems of Certain C27 and C32 Industrial Engines {1261, 1274}
3508, 3512 and 3516 Generator Set Engines Cylinder Head - Assemble
3508, 3512 and 3516 Generator Set Engines Connecting Rod Bearings - Remove and Install
C32 Auxiliary Engine Emergency Stopping
C18 Marine Engine Maintenance Interval Schedule
C13 Industrial Engines Engine Oil Pan
C13 Industrial Engines Engine Oil Pan
C13 Industrial Engines Engine Oil Pan
3508, 3512 and 3516 Generator Set Engines Balancer Group (Front) - Remove and Install - 3508 Engine
G3500B Engines Engine Governing - Adjust
Hydraulic Excavator Idler Disassembly and Assembly Procedures {0729, 4159} Hydraulic Excavator Idler Disassembly and Assembly Procedures {0729, 4159}
2009/12/03 Gasket for the Water Pump on 3054C, 3054E, C4.4 and C6.6 Engines {1361, 1395, 7555}
3508, 3512 and 3516 Generator Set Engines Gear Group (Rear) - Remove and Install