Differential
Show/hide table
Illustration 1 | g06193341 |
Refer to Disassembly and Assembly, "Differential and Bevel Gear Assemble" for the assembly procedure.
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | 2 | 273-0178 Side Gear | Ensure that the four spider gears rotate freely after installation of spider shaft and the side gears rotate after the cover is installed. |
2 | 4 | 6K-1984 Dowel | Installation depth (B) in the housing (3) is |
Show/hide table
Illustration 2 | g06193316 |
View A-A |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
4 | 12 | 267-8628 Locking Bolt | Use the following sequence to tighten the bolts as shown in Illustration 2. |
Show/hide table
Illustration 3 | g06196576 |
View A-A |
Show/hide table
Illustration 4 | g06196577 |
View A-A |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
5 | 40 | 515-8949 Bolt | Use the following procedure to assemble bevel gear to housing: 1. Tighten the bolts 1-8 in a cross pattern to 2. Tighten the bolts 1-40 in a circular pattern to 3. Turn the bolts 1-40 to an extra 30 ± 5 degrees. |
Show/hide table
Illustration 5 | g06193318 |
View C-C |
Show/hide table
Illustration 6 | g06196581 |
View C-C |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
6 | 27 | 6V-7742 Full Nut | Use the following procedure to assemble the pinion gear to hub: 1. Tighten the nuts 1-4 in a cross pattern to 2. Tighten the nuts 1-27 in a circular pattern to |
Note: If either the gear or hub was replaced, or not assembled as a matched set in the same orientation as before disassembly, the following reaming procedure must be done.
Note: Assemble pinion gear to the hub and ream one hole for bolts (6) to
Caterpillar Information System:
797F and 797F XQ Off-Highway Truck Steering System Solenoid Valve (Steering)
797F and 797F XQ Off-Highway Truck Steering System Solenoid and Relief Valve (Steering)
C7.1 Industrial Engine and Generator Set Diesel Particulate Filter Collects Excessive Soot
797F and 797F XQ Off-Highway Truck Power Train Relief Valve (Transmission Main)
797 Off-Highway Truck Braking System Service and Parking Brake (Rear)
797F and 797F XQ Off-Highway Truck Power Train Torque Converter Housing
G3512E and G3520E Generator Set Engines Air/Fuel Ratio Control
C11, C13, and C15 On-highway Engines Monitoring System
C11, C13, and C15 On-highway Engines Configuration Parameters
Piston Seizures on C18 Engines{1225, 1331} Piston Seizures on C18 Engines{1225, 1331}
C7.1 Industrial Engine Exhaust Sensor and Lines (NRS)
C3.4B Engines for Caterpillar Built Machines Alternator - Test
C7.1 Industrial Engine and Generator Set Injector Code - Calibrate
2009/08/17 A New Hose Assembly for the Coolant Outlet from the Turbocharger Is Used on Some 3508B and 3512B Engines {1355, 1380, 1393}
2010/10/08 Proper Placement of the Speed Control for Some Gas Engines {1264, 1716, 1908}
C175 Generator Sets Generator Operation
C13 Industrial Engines Electronic Unit Injector
G3304B and G3306B Engines Flywheel - Remove and Install
G3512E and G3520E Generator Set Engines Electronic Control System Parameters
G3304B and G3306B Engines Flywheel Housing - Remove
C175-16 Locomotive Engine Engine Governing - Adjust
797F and 797F XQ Off-Highway Truck Power Train Transmission Hydraulic Control
C13, C15, and C18 Tier 4 Interim Engines ARD Is Disabled
G3304B and G3306B Engines Flywheel Housing - Install