Air Inlet Heater - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud M8 - 1.25 by 100 mm |
2 |
Start By:
- Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect harness assemblies (1) from air inlet heater (3). Remove the air inlet heater solenoid from the engine.
- Remove hose assembly (2), if necessary.
- Remove air inlet heater (3).
Show/hide table
Illustration 1 | g01466907 |
Note: Ensure that Tooling (A) is installed in the cylinder head.
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud M8 - 1.25 by 100 mm |
2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position air inlet heater (3) on Tooling (A).
- Install hose assembly (2), if necessary.
- Install the air inlet heater solenoid on the engine. Connect harness assemblies (1) to air inlet heater (3).
Show/hide table
Illustration 2 | g01466907 |
End By:
- Install the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Install".
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Inlet Air Is Restricted
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is Low - Fuel Supply System
C7 PETROLEUM Petroleum Engine Aftercooler - Install
C175-16 and C175-20 Generator Set Engines Fuel Filter Is Restricted
C175-16 and C175-20 Generator Set Engines Engine Overspeeds
C7 PETROLEUM Petroleum Engine Aftercooler - Remove
2008/03/03 A New Oil Filter Group is Now Used on the TH48-E80 Oil/Gas Transmission {3030, 3067}
C15 Industrial Engines Configuration Parameters
CX28 On-Highway Transmission Output Transfer Yoke
C175-16 and C175-20 Generator Set Engines Engine Does Not Crank
2008/05/01 A New Version of Caterpillar Electronic Technician (ET) is Now Available {0785, 1900, 7610}
2008/05/26 A New Version of Caterpillar Electronic Technician (ET) is Now Available {0785, 1900, 7610}
C9T-TH31 Petroleum Package Walk-Around Inspection
C11, C13, and C15 On-highway Engines Reference Material
2008/03/01 Visible Indication for Engagement of the Electrical Connector has Been Added to the Ignition Coil for the Caterpillar Regeneration System (CRS) {108B}
SR5 Electric Power Generation Diode Assembly - Remove and Install
C175-16 Locomotive Engine Exhaust Manifold
C175-16 and C175-20 Generator Set Engines Component Location
3500 Industrial Engines Exhaust Flange
C15 On-Highway Engine Combustion Head Group (ARD) - Remove and Install - Heated Nozzle
Bench Test Procedure for TH55FT - E70 and TH55FT - E90 Oil Field Transmission{3030, 3167} Bench Test Procedure for TH55FT - E70 and TH55FT - E90 Oil Field Transmission{3030, 3167}
PL1000E Quick Reference Guide{7610} PL1000E Quick Reference Guide{7610}
2008/06/09 A New Antenna For The Product Link Is Available {7010, 733T}
SR5 Electric Power Generation Terminal Box - Remove and Install