Rocker Arm and Shaft - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 4C-9506 | Retaining Compound | 1 |
B | 169-5464 | Quick Cure Primer | 1 |
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
- Lubricate the contact points of pushrods (4) with clean engine oil. Install pushrods (4). Position rocker arm and shaft (3).
- Install bolts (2) and nuts (1). Tighten bolts (2) and nuts (1) to standard torque.
- Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit Injector - Adjust".
- Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
Show/hide table
Illustration 1 | g01265747 |
Show/hide table
Illustration 2 | g01261872 |
Note: Apply Tooling (A) and Tooling (B) to the threads of studs (1) at Location (X). Wipe off all excess sealant. The three slots of the nut must be free of sealant.
End By:
- Install the variable valve actuator. Refer to Disassembly and Assembly, "Valve Actuator (Variable) - Remove and Install".
Caterpillar Information System:
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 740 - FMI 3
C11 and C13 Petroleum Engines Rocker Arm and Shaft - Remove
G3406 Engine Engine Auxiliary Sump Oil - Change
C7 and C9 On-Highway Engines Timer Parameters
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 738 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 737 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 736 - FMI 3
2006/06/01 An Improved Speed-Timing Sensor is Now Available {1912}
2006/04/17 New Speed Timing Sensor Available {1912}
C13 Engine Electronic Unit Injector Sleeve - Install
C7 On-Highway Engine Fuel Manifold (ARD) - Install
CX31 On-Highway Transmission Gear Pump (Transmission)
CX28 On-Highway Transmission Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
C4.4 Industrial Engine Belt Tension Chart
C4.4 Industrial Engine Water Temperature Regulator and Housing
C4.4 Industrial Engine Engine Oil Pan
C15 On-Highway Engine Valve Actuator (Variable) - Remove
C15 On-Highway Engine Valve Actuator (Variable) - Install
C9.3 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C9.3 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C7 On-Highway Engine Pistons and Connecting Rods - Assemble
3500B Industrial Engines with the ADEM 3 Electronic Control Module System Overview
2006/04/17 A New Impeller is Now Used in the Sea Water Pump of Marine Engines {1371}
C7 PETROLEUM Petroleum Engine Air Inlet Heater - Remove and Install