Camshaft - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil.
- Carefully install camshaft (18) and camshaft gear (4) in cylinder block (19). Be careful not to damage the lobes of the camshaft or the camshaft bearings.
Show/hide table
Illustration 1 | g01201605 |
Typical example |
- Align the bolt holes in camshaft retainer (17) with the bolt holes in the cylinder block. Rotate camshaft gear (4) in order to align access hole (16) in the camshaft gear with the hole for bolt (14). Install bolt (14) and bolt (15) that secures camshaft retainer (17) in position on the cylinder block. Tighten bolt (14) and bolt (15) to a torque of 11 N·m (95 lb in).
Show/hide table
Illustration 2 | g01201600 |
Typical example |
- Install thrust washer (7) on idler hub (6) .
Show/hide table
Illustration 3 | g01201596 |
Typical example |
Show/hide table
Illustration 4 | g01201592 |
Typical example |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
- Install idler gear (5) on idler hub (6) .
Note: When you install the idler gear, ensure that timing marks (2) are aligned on the following components.
- Camshaft gear (4)
- Idler gear (5)
- Crankshaft gear (3)
- Camshaft gear (4)
- Install inner rotor (8) in idler gear (5) .
- Install the following items on idler hub (6) :
- Oil pump cover (9)
- Shim (10)
- Spring (11)
- Collar (12)
- Oil pump cover (9)
- Install retaining ring (13) on idler hub (6) .
- Install slider (1) on camshaft gear (4) .
End By:
- Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Install".
- Install the fuel injection pump. Refer to Disassembly and assembly, "Fuel Injection Pump - Install".
- Install the lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Caterpillar Information System:
Modifying the Air Shutoff Valve{1078, 1078} Modifying the Air Shutoff Valve{1078, 1078}
C175-16 and C175-20 Engines for Caterpillar Built Machines Valve Cover - Remove and Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Bucket - Remove
C1.5 and C2.2 Generator Set Engines Camshaft - Remove
2005/12/19 New Air Shutoff Valves are Now Used {1078}
G3600 Engines Engine Protective Device Connections - Inspect
C15 Generator Set Engines Emergency Stop Switch Circuit - Test
C15 Generator Set Engines Diagnostic Code Cross Reference
C15 Generator Set Engines Engine Pressure Sensor Open or Short Circuit - Test
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C1.5 and C2.2 Generator Set Engines Cylinder Head - Install
2005/09/12 Remanufactured Rocker Arm has been Changed {1123}
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Selector Valve (Alternate Pattern Control) - Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Adjuster - Disassemble
C1.5 and C2.2 Generator Set Engines Pistons and Connecting Rods - Remove
Hydraulic Cylinder Seal Failure Analysis {7555, 7562} Hydraulic Cylinder Seal Failure Analysis {7555, 7562}
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Upper Frame and Undercarriage Frame - Connect
Start-up Procedure after a System Generated Shutdown{1000} Start-up Procedure after a System Generated Shutdown{1000}
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track Adjuster - Assemble
C15 Generator Set Engines CAN Data Link Circuit - Test
3412 Generator Set Engines Fuel Injection Pump Housing
C1.5 and C2.2 Generator Set Engines Pistons and Connecting Rods - Install
C15 Generator Set Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
3412 Generator Set Engines Fuel Injection Pump