Loader Frame and Rear Frame - Connect
连接步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 8T-5255     | 液压千斤顶     | 1     |
B     | 4C-5809     | 电动液压泵总成     | 1     |
9U-7540 | 起吊台架     | 1     | |
C     | 1U-7501     | 加长管     | 2     |
1U-7498 | 支撑支座组件     | 2     | |
D     | 3S-6224     | 电动液压泵总成     | 1     |
6V-3175 | 双作用油缸     | 1     | |
6V-2097 | 套筒     | 1     | |
5P-8601 | 轴承拆卸工具适配器     | 1     | |
5P-4184 | 工具双头螺栓     | 1     | |
9U-6832 | 螺母     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
E     | 1P-1861     | 挡圈钳     | 1     |
F     | 5P-0960     | 含钼润滑脂     |     |
G     | 1P-0491     | 传动板 (1)     | 1     |
1P-0492 | 传动板 (1)     | 1     | |
8S-4710 | 螺栓     | 1     | |
9S-8750 | 螺母     | 1     | |
5P-0537 | 硬垫圈     | 2     | |
H     | 1P-0520     | 冲头总成     | 1     |
Show/hide table
( 1 ) | 1P-0510 冲头总成 零件 |
- 将轴承 (38) 安装到下部铰接中。 使用工具 (E) 安装挡圈 (37) 。
Show/hide table
图 1 | g01058361 |
- 冷却轴承杯 (36) 。 将轴承杯 (36) 安装到上部铰接中。
Show/hide table
图 2 | g01058360 |
- 将工具 (F) 涂抹到轴承内圈 (35) 和轴承内圈 (34) 上。 将轴承内圈 (35) 和轴承内圈 (34) 安装到上部铰接中。
- 冷却轴承杯 (33) 。 将轴承杯 (36) 安装到上部铰接中。
- 将垫片 (31) 安装到上部铰接上。
Show/hide table
图 3 | g01058356 |
- 将盖 (29) 安置到上部铰接上。 润滑脂加油嘴 (27) 必须朝向机器右侧。 安装三个螺栓 (28) 。
Show/hide table
图 4 | g01058460 |
- 使用工具 (G) 检查滚动扭矩。 滚动扭矩必须不小于 3 N·m (27 lb in) 且不大于 10 N·m (89 lb in)。 调整垫片,以便达到正确的滚动扭矩。
Show/hide table
图 5 | g01058461 |
- 安装其余的螺栓 (28) 。 将工具 (F) 涂抹在唇型密封 (30) 和 (32) 上。 使用工具 (H) 安装唇型密封 (30) 和 (32) 。
Show/hide table
图 6 | g01058513 |
- 将隔套 (26) 安装到上部铰接中。
Show/hide table
图 7 | g01058353 |
Show/hide table
图 8 | g01058848 |
- 将工具 (B) 安装到机器前部。 将工具 (C) 安装到机器后部。
Show/hide table
图 9 | g01058282 |
- 拆下螺栓 (18) 。 使用工具 (A) 将销组件 (17) 从下部铰接上拆下。
Show/hide table
图 10 | g01058284 |
- 拆下螺栓 (14) 。 使用工具 (A) 将销组件 (13) 从转向油缸 (15) 上拆下。 拆下止推垫圈 (16) 。
Show/hide table
图 11 | g01058279 |
Show/hide table
图 12 | g01058280 |
- 对机器另一侧,重复步骤 13。
- 安置支架组件 (11) 。 安装螺栓 (12) 。
Show/hide table
图 13 | g01058278 |
- 将软管组件 (9) 连接到机器后部上。
Show/hide table
图 14 | g01058249 |
- 将软管组件 (10) 连接到机器后部上。
Show/hide table
图 15 | g01058275 |
- 将软管组件 (8) 连接到机器前部上。
Show/hide table
图 16 | g01058236 |
- 将制动器电缆 (7) 连接到机器后部上。
Show/hide table
图 17 | g01058222 |
- 连接软管组件 (6) 。
Show/hide table
图 18 | g01058316 |
- 安装新的电缆扎带 (5) 。
Show/hide table
图 19 | g01058314 |
- 定位托架组件 (4) 。 安装螺栓 (3) 。
Show/hide table
图 20 | g01058221 |
- 连接导线 (1) 。 安装新的电缆带 (2) 。
Show/hide table
图 21 | g01058220 |
- 向液压油箱注油。 请参考操作和维护手册, "润滑剂粘度和加注容量"。
End By:
- 安装驱动轴。 请参考 拆解和装配, "主传动轴 - 安装"。
- 安装驾驶室。 请参考 拆解和装配, "驾驶室 - 安装"。
Caterpillar Information System:
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Loader Frame and Rear Frame - Separate
980H Wheel Loader Diagnostic Lines (Remote Pressure Taps) - If Equipped
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0041 - FMI 04
545 Wheel Skidder Machine Systems Hydraulic Rotator - Assemble - Continuous Rotator Grapple
992G Wheel Loader and 854G Wheel Dozer Power Train General Information
950G Series II Wheel Loader Safety
966G II and 972G II Wheel Loaders Aggregate Autodig - If Equipped
2004/03/22 An Unknown Diagnostic Fault Code is Displayed on the CAT Electronic Service Tool Display {1901}
980H Wheel Loader Cooling System Coolant Sample (Level 2) - Obtain
980H Wheel Loader Cooling System Coolant Sample (Level 1) - Obtain
992G Wheel Loader Automatic Lubrication System Components - Check
120H and 135H Motor Graders Air System and Brakes Check Valve (Air Tank)
992G Wheel Loader Plate Locations and Film Locations
D6N Track-Type Tractor Machine Systems Pilot Control Valve - Install
980H Wheel Loader Transmission Oil Filter - Replace
2004/04/12 Internal Changes Improve the Nitrogen Retention of the Accumulators {5077}
980H Wheel Loader Transmission Oil Sample - Obtain
AD30 Underground Articulated Truck Braking System Brake Disc Wear - Check
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System Speed Sensor (Transmission Output) - Replace
992G Wheel Loader Electrohydraulic System Hydraulic Oil Contamination - Test
D6N Track-Type Tractor Machine Systems Pilot Control Valve - Disassemble
2004/04/19 Updated Ejector Lines Group Improves Retention of the Ejector Lines {5057, 6203}
980H Wheel Loader Battery - Clean
AccuGrade Laser System Bank Valve (Grade Control)