Diagnostic Code Cross Reference
Problems with the electronic control system are reported via these types of codes: flash codes, SPN/FMI codes, diagnostic codes and event codes.
For information on flash codes, refer to Troubleshooting, "Flash Codes".
For information on SPN/FMI codes, refer to Troubleshooting, "Diagnostic Codes".
For information on diagnostic codes, refer to Troubleshooting, "Diagnostic Codes".
For information on event codes, refer to Troubleshooting, "Event Codes".
Use Table 1 as a cross-reference between the various types of codes.
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Show/hide table
Cross Reference for Diagnostic Codes | |||
---|---|---|---|
Flash Code | Diagnostic Code
or Event Code |
SPN/FMI Code | Description of Code |
N/A | E443-1 | 1387-15 | High Auxiliary Pressure Warning |
E443-2 | 1387-16 | High Auxiliary Pressure Derate | |
E443-3 | 1387-00 | High Auxiliary Pressure Shutdown | |
E444-1 | 1387-17 | Low Auxiliary Pressure Warning | |
E444-2 | 1387-18 | Low Auxiliary Pressure Derate | |
E444-3 | 1387-01 | Low Auxiliary Pressure Shutdown | |
E445-1 | 441-15 | High Auxiliary Temperature Warning | |
E445-2 | 441-16 | High Auxiliary Temperature Derate | |
E445-3 | 441-00 | High Auxiliary Temperature Shutdown | |
E446-1 | 441-17 | Low Auxiliary Temperature Warning | |
E446-2 | 441-18 | Low Auxiliary Temperature Derate | |
E446-3 | 441-01 | Low Auxiliary Temperature Shutdown | |
15 | 164-02 | 0164-02 | Injector Actuation Pressure Signal erratic |
164-03 | 0164-03 | Injector Actuation Pressure voltage high | |
164-04 | 0164-04 | Injector Actuation Pressure voltage low | |
17 | 164-00 | 0164-00 | High Injector Actuation Pressure |
18 | 042-11 | N/A | Injection Actuation Control Valve open/short |
21 | 262-03 | 0620-03 | 5 Volt Sensor DC Power Supply short to +batt |
262-04 | 0620-04 | 5 Volt Sensor DC Power Supply short to ground | |
263-03 | 0678-03 | Digital Sensor Supply short to +batt | |
263-04 | 0678-04 | Digital Sensor Supply short to ground | |
24 | 100-03 | 0100-03 | Engine Oil Pressure open/short to +batt |
100-04 | 0100-04 | Engine Oil Pressure short to ground | |
25 | 273-03 | 0102-03 | Turbo Outlet Pressure open/short to +batt |
273-04 | 0102-04 | Turbo Outlet Pressure short to ground | |
26 | 274-03 | 0108-03 | Atmospheric Pressure open/short to +batt |
274-04 | 0108-04 | Atmospheric Pressure short to ground | |
27 | 110-03 | 0110-03 | Engine Coolant Temperature open/short to +batt |
110-04 | 0110-04 | Engine Coolant Temperature short to ground | |
28 | 91-13 | 0091-13 | Throttle Position calibration required |
32 | 91-08 | 0091-08 | Throttle Position signal abnormal |
34 | 320-02 | 0190-02 | Speed/Timing Sensor Loss of Signal |
320-11 | 0190-11 | Speed/Timing Sensor mechanical failure | |
342-02 | 0723-02 | Loss of Secondary Engine Speed signal | |
342-11 | 0723-11 | Secondary Engine Speed Sensor mechanical failure | |
35 | E004 | 0190-16 | Engine Overspeed Shutdown |
E190 | 0190-00 | Engine Overspeed Warning | |
37 | 94-03 | 0094-03 | Fuel Pressure open/short to +batt |
94-04 | 0094-04 | Fuel Pressure short to ground | |
175-03 | 0175-03 | Engine Oil Temperature open/short to +batt | |
175-04 | 0175-04 | Engine Oil Temperature open/short to ground | |
38 | 172-03 | 0172-03 | Intake Manifold Air Temp open/short to +batt |
172-04 | 0172-04 | Intake Manifold Air Temp short to ground | |
39 | 164-11 | 0164-11 | Injector Actuation Press Sensor fault |
42 | 261-13 | 0228-13 | Engine Timing calibration required |
46 | E039 | 0100-18 | Low Engine Oil Pressure Derate |
E040 | 0100-01 | Low Engine Oil Pressure Shutdown | |
E100 | 0100-17 | Low Engine Oil Pressure Warning | |
49 | 617-05 | 0729-05 | Air Inlet Heater Relay open/current below normal |
617-06 | 0729-06 | Air Inlet Heater Relay grounded/current above normal | |
51 | 168-02 | 0168-02 | System Voltage intermittent/erratic |
53 | 254-12 | N/A | Electronic Control Module Error |
56 | 253-02 | 0234-02 | Personality Module mismatch |
268-02 | 1111-02 | Check Programmable Parameters | |
58 | 247-09 | 0639-09 | J1939 Data Link communications |
61 | E015 | 0110-16 | High Engine Coolant Temperature Derate |
E016 | 0110-00 | High Engine Coolant Temperature Shutdown | |
E017 | 0110-15 | High Engine Coolant Temperature Warning | |
62 | E057 | 0111-18 | Low Engine Coolant Level Derate |
E058 | 0111-01 | Low Engine Coolant Level Shutdown | |
E059 | 0111-17 | Low Engine Coolant Level Warning | |
63 | E005 | 0094-15 | Fuel Filter Restriction Derate |
E006 | 0094-16 | Fuel Filter Restriction Shutdown | |
E095 | 0094-00 | Fuel Filter Restriction Warning | |
E096 | 0094-00 | High Fuel Pressure | |
64 | E025 | 0172-16 | High Inlet Air Temperature Derate |
E027 | 0172-15 | High Inlet Air Temperature Warning | |
72 | 1-11 | 0651-11 | Injector Cylinder #1 fault |
2-11 | 0652-11 | Injector Cylinder #2 fault | |
73 | 3-11 | 0653-11 | Injector Cylinder #3 fault |
4-11 | 0654-11 | Injector Cylinder #4 fault | |
74 | 5-11 | 0655-11 | Injector Cylinder #5 fault |
6-11 | 0656-11 | Injector Cylinder #6 fault |
Caterpillar Information System:
3508C, 3512C and 3516C Marine Engines Flywheel - Remove and Install
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble
345C Excavator Machine System Specifications Boom
345C Excavator Machine System Specifications Final Drive
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
568 Forest Machine Machine System Specifications Recoil Spring
C9 Marine Generator Set Product Lifting
C32 Marine Engines System Configuration Parameters
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Flash Programming
C9 Engines for Caterpillar Built Machines Basic Engine
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Remove
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Install
2004/12/01 Correct Wiring Diagrams Have Been Identified for 480 Volt Sensing VR3 to VR6 Regulator Conversion {4467}
2004/12/01 New Lockwasher Will Improve Varistor Reliability {4466}
C7.1 Industrial Engine Engine Stopping
C4.4 Industrial Engine Electrical System
C11 and C13 Engines for Caterpillar Built Machines General Information
C11 and C13 Engines for Caterpillar Built Machines Lubrication System
G3520C and G3520E Generator Set Engines Fuel Control Valve - Remove and Install
3126B Petroleum Engine Injection Actuation Pressure - Test
C6.6 Industrial Engine Model View Illustrations
3500 and 3500B Engines Reference Numbers