Bulldozer - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-9906     | Ratchet Puller     | 1     |
- Install bearing (24) and snap ring (25) in cage (21) .
Show/hide table
Illustration 1 | g00727306 |
- Install cage (21), two retainers (23) and six bolts (22) on the right push arm (20) .
Show/hide table
Illustration 2 | g00727335 |
- Use a hoist and Tooling (A) in order to position right push arm (20) on the trunnion and blocks (2) .
Show/hide table
Illustration 3 | g00727302 |
- Install cap (19) and the bolts that hold the right push arm on the trunnion.
- Use a hoist and Tooling (A) in order to position left push arm (17) in cage (21) and on the trunnion. Position the blocks under the left push arm.
Show/hide table
Illustration 4 | g00727360 |
Show/hide table
Illustration 5 | g00727300 |
- Install cap (18) and the bolts that hold the left push arm on the trunnion.
- Position bulldozer blade (12) on the push arms with a hoist.
Show/hide table
Illustration 6 | g00727297 |
- Install the shims, caps (16) and the bolts that hold the shims and caps in place. There must be 0.3 mm (.010 inch) to 0.8 mm (.030 inch) clearance between the cap and the trunnion ball when the cap is installed.
- Position brace (14) on the bulldozer blade with a hoist. Install the shims and cap (13). Install the bolts that hold the shims and the cap in place. There must be 0.3 mm (.010 inch) to 0.8 mm (.030 inch) clearance between the cap and the trunnion ball after the shims and the cap are installed.
Show/hide table
Illustration 7 | g00727295 |
- Put brace (14) into position on the left push arm. Install pin (15) .
- Remove the hoist from the bulldozer blade.
- Install link assembly (10) and pins (11) between the push arm and the bulldozer blade.
Show/hide table
Illustration 8 | g00727291 |
- Fasten a hoist to the rod end of the lift cylinder. Support the weight of the cylinders with the hoist.
Show/hide table
Illustration 9 | g00727287 |
- Extend the lift cylinders until rod assembly (9) is in position on the trunnion ball on the bulldozer blade.
- Install the shims and caps (8). Install the bolts that hold the shims and caps in place. There must be 0.3 mm (.010 inch) to 0.8 mm (.030 inch) clearance between the cap and the trunnion ball after the shims and the cap are installed.
- Fasten a hoist to tilt cylinder (6). Put the tilt cylinder into position on the push arm, and install pin (7) .
Show/hide table
Illustration 10 | g00727286 |
- Put the rod end of the tilt cylinder into position against the trunnion ball. Install the shims and cap (5). Install the bolts that hold the shims and the cap in place. There must be 0.3 mm (.010 inch) to 0.8 mm (.030 inch) clearance between the cap and the trunnion ball after the shims and the cap are installed.
- Position the tilt cylinder hoses. Install the rubber and guard (4) .
Show/hide table
Illustration 11 | g00727285 |
- Connect tilt cylinder hoses (3) to the elbows.
- Raise the bulldozer and remove blocks (2) from push arms (1). Lower the bulldozer.
Show/hide table
Illustration 12 | g00727282 |
End By: Install the bulldozer. Refer to Disassembly and Assembly, "Bulldozer - Install" for the machine that is being serviced.
Caterpillar Information System:
D6M Track-Type Tractor Machine Systems Bulldozer (VPAT) - Remove
D6M Track-Type Tractor Machine Systems Bulldozer (VPAT) - Install
545 Wheel Skidder Fuel System Secondary Filter - Replace
D6M Track-Type Tractor Machine Systems Battery - Remove and Install
D6M Track-Type Tractor Machine Systems Air Conditioner and Heater Fan Motor - Remove and Install
D6M Track-Type Tractor Machine Systems Air Conditioner Dryer - Remove and Install
515 Wheel Skidder and 525 Wheel Skidder Steering Control
637E Series II Wheel Tractor-Scrapers Cushion-Hitch Control
515 Wheel Skidder and 525 Wheel Skidder Window Wiper and Washer Control
623F Wheel Tractor-Scraper Power Train Transmission Electronic Control System
D6R Track-Type Tractor Power Train Brake Control Valve
D6F and D6G Track-Type Tractors Power Train General Information
D6M Track-Type Tractor Machine Systems Bulldozer - Disassemble
D6M Track-Type Tractor Machine Systems Bulldozer - Install
D6M Track-Type Tractor Machine Systems Bulldozer - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Angle Cylinder - Install
D6M Track-Type Tractor Machine Systems Bulldozer Angle Cylinder - Remove
D6M Track-Type Tractor Machine Systems Bulldozer C-Frame - Remove and Install
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Assemble
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Disassemble
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Install
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder - Install
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder - Remove