M316C Wheeled Excavator TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} Caterpillar

Excavator:

M316C (S/N: H2C1-UP; BDX1-UP)

Introduction

Inspections are the most basic form of condition monitoring. Inspections are easy to do and surprisingly effective at helping you spot equipment health issues. Proactive monitoring and analysis of equipment information will allow Dealers to intervene effectively before problems occur.

Note: Before adjusting product settings to comply with listed baseline TA2 values, consult SIS for the latest specification values.

Note: Specification values are based on the following machine settings, unless otherwise stated.

• Engine Speed Dial "10"

• HP Mode

• AEC OFF

• A/C OFF

Creating an Electronic Copy

Use the following procedure to create an editable electronic copy from SIS Web.

1. Click format to print.

2. Save the document as an HTML format.

3. Open the document with Microsoft Word.

Electrical System

Table 1

Status (1)	Description	Specification	Actual	Comments
	Inspect Battery Cables	Cables between the battery, the starter, and the engine ground must be the correct size. Wires and cables must be free of corrosion. Wires and cables must have cable support clamps in order to prevent stress on battery connections (terminals).
	Battery Test	12.4 VDC or more		Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
	Charging System Test	18 VDC to 32 VDC		Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".
	Electric Starting System Test	12 to 16 V at −23° C (−10° F) to −7° C (19° F)		Refer to Testing and Adjusting, RENR2416, "Electric Starting System - Test".
		14 to 18 V at −7° C (19° F) to 10° C (50° F)
		16 to 24 V at 10° C (50° F) to 27° C (80° F)

( 1 )

N = Normal, M = Monitor, A = Action

Engine

Cooling System

Table 2

Status (1)	Description	Specification	Actual	Comments
	Radiator Pressure Relief (Radiator Cap) (2)	-		Refer to System Operation Testing and Adjusting.
	Freezing Point of Engine Coolant	-		Refer to Operation and Maintenance Manual.
	Belt Tension	-		Measure point midway between pulleys. Alternator and fan drive belts will deflect 13 to 19 mm (0.5 to 0.7 inch) with 110 N (25 lb). Air conditioner belt will deflect 7 to 10 mm (0.3 to 0.4 inch) with 98 N (22 lb) force.
	Conditioner Test of Engine Coolant	90° + 3° - 8° C (194.00000° + 37° - 46° F)
	Difference between the Upper and Lower Radiator Tank Temperatures	-

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Test for the pressure that is listed on the cap.

Fuel System

Table 3

Status (1)	Description	Specification	Actual	Comments
	Fuel Pressure at LOW IDLE
	Fuel Pressure at HIGH IDLE	30 kPa (4 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Lubrication System

Table 4

Status (1)	Description	Specification	Actual	Comments
	Engine Oil Pressure at LOW IDLE	100 kPa (15 psi)
	Engine Oil Pressure at HIGH IDLE	200 kPa (29 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Basic Engine for M316C S/N:BDX1-2000

Table 5

"Engine Performance - Test (Engine Speed)"
Status (1)	Description	Specification	Actual	Comments
	Low Idle AEC OFF	1030 to 1060 rpm
	Low Idle AEC ON	950 to 980 rpm
	High Idle No Load	2100 rpm

( 1 )

N = Normal, M = Monitor, A = Action

Basic Engine for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 6

"Engine Performance - Test (Engine Speed)"
Status (1)	Description	Specification	Actual	Comments
	High Idle	2100 rpm
	Full Load	2000 rpm

( 1 )

N = Normal, M = Monitor, A = Action

Air Inlet and Exhaust System

Table 7

Status (1)	Description	Specification	Actual	Comments
	Pump Stall Boost Pressure	99 to 119 kPa (14 to 17 psi)
	Engine Speed - Full Load	2000 rpm
	Desired Main Relief Pressure	18500 to 20500 kPa (2683 to 2973 psi) (2)
	Cylinder # 1 Exhaust Temperature (3)
	Cylinder # 2 Exhaust Temperature (2)
	Cylinder # 3 Exhaust Temperature (2)
	Cylinder # 4 Exhaust Temperature (2)
	Cylinder # 5 Exhaust Temperature (2)
	Cylinder # 6 Exhaust Temperature (2)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP only
( 3 )	Compare the exhaust temperature variance at each exhaust port.

Performance Checks

ReferenceRefer to Testing & Adjusting, RENR5567, "Hydraulic System", and Testing & Adjusting, RENR9125, "Hydraulic System" for more detail on the following test.

Operational Checks

Swing Speed and Overswing on Level Ground - Check

Table 8

Swing Speed and Overswing on Level Ground - Check
Status (1)	Description	Specifications (2)	Actual	Comments
	Left Swing	10 to 10.5
	Right Swing

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Number of Revolutions in 60 seconds.

Cylinder Drift - Check for M316C S/N:BDX1-2000

Table 9

Cylinder Drift Per Minute
Status (1)	Description	Specifications		Actual	Comments
		Pressure
		28000 kPa (4060 psi)	28000 kPa (4060 psi) (3)
	Stick Cylinder	42 mm (1.65 inch) (2)	2.9 mm (0.11 inch) (3)
	Boom Cylinder	14 mm (0.55 inch) (2)	2.9 mm (0.11 inch) (3)
	Bucket Cylinder	33 mm (1.30 inch) (2)	2.9 mm (0.11 inch) (3)
	VA Boom Cylinder	18 mm (0.71 inch) (2)	2.9 mm (0.11 inch) (3)

( 1 )	N = Normal, M = Monitor, A = Action
( 3 )	Maximum drift with lowering control valve
( 2 )	Maximum drift

Cylinder Drift - Check for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 10

Cylinder Drift Per Minute
Status (1)	Description	Specifications		Actual	Comments
		Pressure
		28000 kPa (4060 psi)	28000 kPa (4060 psi) (3)
	Stick Cylinder	37 mm (1.46 inch) (2)	2.9 mm (0.11 inch) (3)
	Boom Cylinder	12 mm (0.47 inch) (2)	2.9 mm (0.11 inch) (3)
	Bucket Cylinder	28 mm (1.10 inch) (2)	2.9 mm (0.11 inch) (3)
	VA Boom Cylinder	14.8 mm (0.58 inch) (2)	2.9 mm (0.11 inch) (3)

( 1 )	N = Normal, M = Monitor, A = Action
( 3 )	Maximum drift with lowering control valve
( 2 )	Maximum drift

Cylinder Speed - Check for M316C S/N:BDX1-2000

Table 11

Cylinder Operating Speed (seconds)
Status (1)	Description	Specifications	Actual	Comments
	Boom Extension	4.6 ± 0.2
	Boom Retraction	6.2 ± 0.2
	Stick Extension	3.2 ± 0.2
	Stick Retraction	3.5 ± 0.2
	Bucket Extension	1.9 ± 0.2
	Bucket Retraction	2.7 ± 0.2
	VA Boom Extension	3.5 ± 0.2
	VA Boom Retraction	10.1 ± 0.2
	Stabilizer Extension	4.7 ± 0.2
	Stabilizer Retraction	5.0 ± 0.2
	Blade Extension	2.3 ± 0.2
	Blade Retraction	2.7 ± 0.2

( 1 )

N = Normal, M = Monitor, A = Action

Cylinder Speed - Check for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 12

Cylinder Operating Speed (seconds)
Status (1)	Description	Specifications	Actual	Comments
	Boom Extension	6.2 ± 0.2
	Boom Retraction	4.6 ± 0.2
	Stick Extension	3.2 ± 0.2
	Stick Retraction	3.5 ± 0.2
	Bucket Extension	1.8 ± 0.2
	Bucket Retraction	2.7 ± 0.2
	VA Boom Extension	3.5 ± 0.2
	VA Boom Retraction	10.2 ± 0.2
	Stabilizer Extension (2)	8.0 ± 0.2
	Stabilizer Retraction (2)	8.0 ± 0.2

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Movement of two cylinders at the same time

Hydraulic System

ReferenceRefer to Testing & Adjusting, RENR5567, "Hydraulic System", and Testing & Adjusting, RENR9125, "Hydraulic System" for more detail on the following test.

Pilot System

Relief Valve (Pilot) - Test and Adjust for M316C S/N:BDX1-2000

Table 13

Status (1)	Description	Specifications	Actual	Comments
	Pilot Pressure	3000 to 3100 kPa (435 to 450 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Pilot) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 14

Status (1)	Description	Specifications	Actual	Comments
	Pilot Pressure	3100 to 3300 kPa (450 to 479 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Accumulator - Test and Charge

Table 15

Status (1)	Description	Specifications	Actual	Comments
	Pilot accumulator gas charge pressure (2)	1000 kPa (145 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Nitrogen gas pressure varies with the temperature. To obtain the most accurate nitrogen charge, the temperature of the accumulator must be identical to the air temperature around the accumulator. The specification is with an air temperature of 21 °C (70 °F). Refer to Testing and Adjusting, RENR9125, "Accumulator - Test and Charge" for additional charging pressure and temperature relationships.

Pump System

Margin Pressure - Test and Adjust for M316C S/N:BDX1-2000

Table 16

Status (1)	Description		Specifications	Actual	Comments
	Low Pressure Standby		2500 to 3000 kPa (363 to 435 psi)
	Margin Pressure (2)		2100 to 2300 kPa (305 to 334 psi)
	Main Pump Pressure		35200 to 36300 kPa (5100 to 5270 psi)
	Load Sensing Signal Limiter Pressure		33000 to 34000 kPa (4790 to 4930 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Use Electronic Technician to override the travel pilot solenoid, with the machine in FIRST GEAR, and the engine speed at the HIGH IDLE position.

Margin Pressure - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 17

Status (1)	Description		Specifications	Actual	Comments
	Low Pressure Standby		2800 to 3500 kPa (406 to 508 psi)
	Margin Pressure (2)		2100 to 2300 kPa (305 to 334 psi)
	Margin Pressure	Hydraulic Modulation 1	1800 ± 200 kPa (261 ± 29 psi)
		Hydraulic Modulation 2	1400 ± 200 kPa (203 ± 29 psi)
		Hydraulic Modulation 3	1000 ± 200 kPa (145 ± 29 psi)
	Main Pump Pressure		35100 to 36300 kPa (5091 to 5265 psi)
	Load Sensing Signal Limiter Pressure		33000 to 34000 kPa (4786 to 4931 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Use Electronic Technician to override the travel pilot solenoid, with the machine in FIRST GEAR, and the engine speed at the HIGH IDLE position.

Main Pump (Proportional Reducing Valve) - Test and Adjust for M316C S/N:BDX1-2000

Table 18

Status (1)	Description		Specifications	Actual	Comments
			No load
	Main pump pressure (Proportional reducing valve)	Mode E	1450 to 1500 kPa (210 to 220 psi)
		Mode P	1940 to 1990 kPa (280 to 290 psi)
		Mode T	2300 to 2350 kPa (335 to 340 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Main Pump (Proportional Reducing Valve) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 19

Status (1)	Description		Specifications	Actual	Comments
			No load
	Main pump pressure (Proportional reducing valve)	Mode E	1450 ± 50 kPa (210 ± 7 psi)
		Mode P	1940 ± 50 kPa (281 ± 7 psi)
		Mode T	2300 ± 50 kPa (334 ± 7 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Main Pump (Destroke Pressure) - Test and Adjust for M316C S/N:BDX1-2000

Table 20

Status (1)	Description	Specifications	Actual	Comments
	Destroke Pressure at Mode P (2)	14500 to 15500 kPa (2105 to 2250 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Use the Electronic Technician to adjust the constant mode from 1970 kPa (285 psi).

Main Pump (Destroke Pressure) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 21

Status (1)	Description	Specifications	Actual	Comments
	Destroke Pressure at Mode P (2)	14500 ± 100 kPa (2103 ± 15 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Use the Electronic Technician to adjust the constant mode from 1970 kPa (285 psi).

Main Pump (Unloading Valve) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 22

Status (1)	Description	Specifications	Actual	Comments
	Main Pump Pressure	2800 to 3400 kPa (406 to 493 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Main Control Valve System

Relief Valve (Main) - Test and Adjust

Table 23

Status (1)	Description	Specifications	Actual	Comments
	Main Relief Valve (implement or travel)	41000 to 43000 kPa (5947 to 6237 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Signal Limiter) - Test and Adjust

Table 24

Status (1)	Description	Specifications	Actual	Comments
	Signal Limiter Relief Valve pressure	33000 to 34000 kPa (4786 to 4931 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Line) - Test and Adjust - Implement

Table 25

Status (1)	Description			Specifications	Actual	Comments
	Line relief valve	Boom Cylinder	Head End	38000 to 40000 kPa (5512 to 5802 psi)
			Rod End
		Stick Cylinder	Head End
			Rod End
		Bucket Cylinder	Head End
			Rod End
		VA Boom Cylinder	Head End
			Rod End	40000 to 42000 kPa (5802 to 6092 psi)
		Combined function (3)		36000 to 38000 kPa (5220 to 5510 psi) (4)
		Combination Valve (2)		41000 kPa (5947 psi) (5)

( 1 )	N = Normal, M = Monitor, A = Action
( 3 )	This circuit should be set according to the attachment that is going to be used on the machine. The pressure should never exceed 42000 kPa (6090 psi)
( 4 )	for M316C S/N:BDX1-2000
( 2 )	This circuit should be set according to the attachment that is going to be used on the machine. The pressure should never exceed 41000 kPa (5947 psi).
( 5 )	for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Boom System

Control Valve (Boom Lowering) - Test and Adjust for M316C S/N:BDX1-2000

Table 26

Status (1)	Description	Specifications	Actual	Comments
	Lowering Control Valve pressure	36000 to 40000 kPa (5220 to 5800 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Control Valve (Boom Lowering) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 27

Status (1)	Description	Specifications	Actual	Comments
	Lowering Control Valve pressure	38000 to 40000 kPa (5512 to 5802 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Pressure Switch (Overload Warning) - Test and Adjust for M316C S/N:BDX1-2000

Table 28

Status (1)	Description	Specifications	Actual	Comments
	Overload Warning Pressure	16000 kPa (2320 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Pressure Switch (Overload Warning) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 29

Status (1)	Description	Specifications	Actual	Comments
	Overload Warning Pressure	15000 to 16500 kPa (2175 to 2393 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Stick System

Control Valve (Stick Lowering) - Test and Adjust for M316C S/N:BDX1-2000

Table 30

Status (1)	Description	Specifications	Actual	Comments
	Lowering Control Valve pressure	36000 to 40000 kPa (5220 to 5800 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Control Valve (Stick Lowering) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 31

Status (1)	Description	Specifications	Actual	Comments
	Lowering Control Valve pressure	38000 to 40000 kPa (5512 to 5802 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Swing System

Swing Pump Control (Mechanical Zero) - Test and Adjust for M316C S/N:BDX1-2000

Table 32

Status (1)	Description	Specifications	Actual	Comments
	Swing charge pump pressure	2200 kPa (320 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Swing Pump Control (Mechanical Zero) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 33

Status (1)	Description	Specifications	Actual	Comments
	Swing charge pressure (pump)	2000 to 2200 kPa (290 to 319 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Swing Pump Control (High Pressure Cutoff) - Test and Adjust for M316C S/N:BDX1-2000

Table 34

Status (1)	Description	Specifications	Actual	Comments
	Swing cutoff pressure	37000 to 38500 kPa (5365 to 5585 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Swing Pump Control (High Pressure Cutoff) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 35

Status (1)	Description	Specifications	Actual	Comments
	Swing cutoff pressure	37000 to 38500 kPa (5366 to 5584 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Swing Brake Pressure - Test for M316C S/N:BDX1-2000

Table 36

Status (1)	Description	Specifications	Actual	Comments
	Swing Brake Pressure	3000 to 3100 kPa (435 to 450 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Swing Brake Pressure - Test for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 37

Status (1)	Description	Specifications	Actual	Comments
	Swing Brake Pressure	3000 to 3300 kPa (435 to 479 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Solenoid Valve (Swing Pump Proportional Relief) - Test and Adjust for M316C S/N:BDX1-2000

Table 38

Status (1)	Description		Specifications	Actual	Comments
	Swing pump pressure (Proportional relief valve)	Mode E	1000 to 1050 kPa (145 to 150 psi)
		Mode P	1550 to 1600 kPa (225 to 230 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Solenoid Valve (Swing Pump Proportional Relief) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 39

Status (1)	Description		Specifications	Actual	Comments
	Swing pump pressure (Proportional relief valve)	Mode E	1050 ± 50 kPa (152 ± 7 psi)
		Mode P	1600 ± 50 kPa (232 ± 7 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Swing Charge Pressure) - Test and Adjust for M316C S/N:BDX1-2000

Table 40

Status (1)	Description	Specifications	Actual	Comments
	Swing Charge Pressure	2200 kPa (320 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Swing Charge Pressure) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 41

Status (1)	Description	Specifications	Actual	Comments
	Swing Charge Pressure	2000 to 2200 kPa (290 to 320 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Swing Pump) - Test and Adjust for M316C S/N:BDX1-2000

Table 42

Status (1)	Description	Specifications	Actual	Comments
	Line relief valve - Swing	38200 ± 40200 kPa (5540 ± 5830 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Swing Pump) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 43

Status (1)	Description	Specifications	Actual	Comments
	Line relief valve - Swing	38200 ± 40200 kPa (5541 ± 5831 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Travel System

Travel Motor (Destroke Point) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 44

Status (1)	Description	Specifications	Actual	Comments
	Destroke Pressure	550 ± 50 kPa (80 ± 7 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Travel Motor (Upstroke Pressure) - Test and Adjust for M316C S/N:BDX1-2000

Table 45

Status (1)	Description	Specifications	Actual	Comments
	Upstroke Pressure	25000 to 26000 kPa (3625 to 3770 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Travel Motor (Upstroke Point) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 46

Status (1)	Description	Specifications	Actual	Comments
	Upstroke Pressure	26000 to 27000 kPa (3771 to 3916 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Travel Motor (Stall Pressure) - Test and Adjust for M316C S/N:BDX1-2000

Table 47

Status (1)	Description	Specifications	Actual	Comments
	Travel Motor (Stall Pressure)	33000 to 34000 kPa (4786 to 4931 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Travel Motor (Drive Shaft Speed) - Test and Adjust for M316C S/N:BDX1-2000

Table 48

Status (1)	Description	Specifications	Actual	Comments
	Drive Shaft Speed in First Gear Activated Creeper Speed (Forward and Reverse) at a hydraulic oil temperature of 55° ± 5°C (131° ± 9°F) (2)	267 ± 10 rpm

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	The specifications are for a machine with the wheels above the ground. Drive shaft speed will be 10 percent lower than the value if the drive shaft speed is measured with the wheels on the ground.

Relief Valve (Travel Motor) - Test and Adjust

Table 49

Status (1)	Description	Specifications	Actual	Comments
	Travel System Pressure	42000 kPa (6092 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Steering and Brake Systems

Accumulator (Wheel Brake Charge Pressure) - Test and Adjust for M316C S/N:BDX1-2000

Table 50

Status (1)	Description	Specifications	Actual	Comments
	Service Brake Accumulator Gas Charge Pressure (2)	4500 to 5000 kPa (650 to 725 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Nitrogen gas pressure varies with the temperature. To obtain the most accurate nitrogen charge, the temperature of the accumulator must be identical to the air temperature around the accumulator. The specification is with an air temperature of 21 °C (70 °F). Refer to Testing and Adjusting, "Accumulator - Test and Charge" for additional charging pressure and temperature relationships.

Accumulator (Wheel Brake Charge Pressure) - Test and Adjust for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 51

Status (1)	Description	Specifications	Actual	Comments
	Service Brake Accumulator Gas Charge Pressure (2)	4500 kPa (650 psi)

( 1 )	N = Normal, M = Monitor, A = Action
( 2 )	Nitrogen gas pressure varies with the temperature. To obtain the most accurate nitrogen charge, the temperature of the accumulator must be identical to the air temperature around the accumulator. The specification is with an air temperature of 21 °C (70 °F). Refer to Testing and Adjusting, "Accumulator - Test and Charge" for additional charging pressure and temperature relationships.

Relief Valve (Steering) - Test for M316C S/N:BDX1-2000

Table 52

Status (1)	Description	Specifications	Actual	Comments
	Steering pressure	21000 to 22500 kPa (3045 to 3260 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Relief Valve (Steering) - Test for M316C S/N:BDX2001-UP and ; S/N:H2C1-UP

Table 53

Status (1)	Description	Specifications	Actual	Comments
	Steering pressure	19500 to 21000 kPa (2828 to 3046 psi)

( 1 )

N = Normal, M = Monitor, A = Action

Work Tool Systems

Relief Valve (Medium Pressure Function) - Test and Adjust

Table 54

Status (1)	Description	Specifications	Actual	Comments
	Line relief valve	21000 to 23000 kPa (3046 to 3336 psi)
	Relief valve	17500 to 18500 kPa (2538 to 2683 psi)

( 1 )

N = Normal, M = Monitor, A = Action

S.O.S

ReferenceRefer to Operation and Maintenance Manual, SEBU7945, "Maintenance Interval Schedule" and Operation and Maintenance Manual, SEBU7430, "Maintenance Interval Schedule" for more detail on performing S.O.S samples.

Table 55

Status (1)	Description	Obtain		Comments
	Engine Oil Sample
	Engine Coolant Sample (Level II)
	Hydraulic Oil Sample
	Swing Drive Oil Sample
	Right Final Drive Oil Sample
	Left Final Drive Oil Sample

( 1 )

N = Normal, M = Monitor, A = Action