Cylinder Head - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
开始:
- 拆下排气歧管。 请参阅拆解和组装, "排气歧管 - 拆卸和安装"。
- 拆下摇臂轴和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 拆下进气歧管。 请参阅拆解和组装, "进气歧管 - 拆卸"。
- 拆下水温调节器壳体。 请参阅拆解和组装, "水温调节器- 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
注: 3064 发动机有一个气缸盖,而 3066 发动机则有两个。
- 逐步将缸盖螺栓 (1) 从缸盖上拆下。 3066 发动机有 13 条缸盖螺栓,而 3064 发动机有 17 条。 采用与上紧过程相反的顺序拆下螺栓。
Show/hide table
图 1 | g00527527 |
缸盖螺栓的上紧顺序( 3066 发动机) |
Show/hide table
图 2 | g00527556 |
缸盖螺栓的上紧顺序( 3064 发动机) |
Show/hide table
图 3 | g00604993 |
- 将工具 (A) 、吊链和适当的起吊设备安装到缸盖 (2) 上。
注: 不要利用撬棍撬开缸盖和缸体。
Show/hide table
图 4 | g00605044 |
典型实例 |
- 将缸盖 (2) 从缸体上拆下。 3066 发动机缸盖组件的重量为 32 kg (70 lb)。 3064 发动机缸盖组件的重量为 45 kg (100 lb)。
注: 将缸盖放在不会使缸盖表面产生损失的表面上。
- 将缸盖密封垫 (3) 从缸体上拆下。
Show/hide table
图 5 | g00605078 |
注: 从缸体上拆卸密封垫时,当心不要损伤缸体的安装面。
- 对其他缸盖重复步骤 1 到步骤 4( 3066 发动机)。
Caterpillar Information System:
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Shutoff Solenoid
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Head - Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Pilot Control Valve (Auxiliary)
365B and 365B Series II Excavators Supplement for 3196 Engine Expansion Tank - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3126B Engine for Caterpillar Built Machines Coolant Temperature Sensor
3176C and 3196 Engines for Caterpillar Built Machines Fuel Temperature Sensor - If Equipped
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0542 - FMI 02 Unfiltered Engine Oil Pressure misinstalled
318B Excavator Machine System Specifications Stick Cylinder
318B Excavator Machine System Specifications Bucket Cylinder
322B, 322B L, 325B and 325B L Excavators Maintenance Interval Schedule
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Fuel Conservation Practices
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Relief Valve (One-Way Hydraulic Flow)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
365B and 365B Series II Excavators Supplement for 3196 Engine Crankcase Breather - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Drift Reduction Valve (Stick) - Remove
Guidelines for the Use of Clean Out Filters for the Hydraulic Oil System and for the Power Train Oil System{3067, 5068} Guidelines for the Use of Clean Out Filters for the Hydraulic Oil System and for the Power Train Oil System{3067, 5068}
5230B Excavator Fire Extinguisher Location
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Drift Reduction Valve (Stick) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Aftercooler
3064 and 3066 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
LR15 and LR18 Landscape Rakes Mounting Bracket - Inspect
365B and 365B Series II Excavators Supplement for 3196 Engine Engine Oil Filler - Remove and Install