Electric Starting Motor - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Put identification on cable assemblies for installation purposes. Remove cable assemblies for ground terminal (1) and (2). Remove cable assembly for switch terminal (3) and cable assembly for battery terminal (4).
Show/hide table
Illustration 2 g00565145 - Use a suitable lifting device to support the electric starting motor. The weight of the electric starting motor is approximately
34 kg (75 lb) . Remove bolts (6) and electric starting motor (5).
Show/hide table
Illustration 1 | g00565140 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use a suitable lifting device to position electric starting motor (5). The weight of the electric starting motor is approximately
34 kg (75 lb) . Install bolts (6).Show/hide tableIllustration 4 g00565140 - Install cable assemblies for ground terminal (1) and (2), cable assembly for switch terminal (3), and cable assembly for battery terminal (4) on the electric starting motor. Tighten the nuts to the following torques:
- Tighten cable assemblies for ground terminal (1) and (2) to a torque of
31 ± 4 N·m (22 ± 3 lb ft) . - Tighten cable assembly for switch terminal (3) to a torque of
2.25 ± 0.25 N·m (20 ± 2 lb in) . - Tighten cable assembly for battery terminal (4) to a torque of
31 ± 4 N·m (22 ± 3 lb ft) .
- Tighten cable assemblies for ground terminal (1) and (2) to a torque of
Show/hide table
Illustration 3 | g00565145 |
Caterpillar Information System:
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Crank Terminate Speed Calibration
3508B, 3512B, and 3516B High Displacement Generator Sets Fuel Injector - Inspect/Adjust
3500 and 3500B Engines Fuel System Fuel Filter Differential Pressure - Check
3508B, 3512B, and 3516B High Displacement Generator Sets Engine Oil Filter Differential Pressure - Check
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Overspeed Calibration
3500B Locomotive Engines Air Compressor - Inspect
3508B, 3512B, and 3516B High Displacement Generator Sets Prelube Pump - Inspect
3500B and 3500 Marine Propulsion Engines with EUI Option Electric Starting Motor - Inspect
3500B High Displacement Generator Set Engines Air Starting Motor - Inspect
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Overspeed Verification Test
Generator Set Control Panel for Switchgear Conversion CID 0828 FMI 08 Temperature Sensor (Right Exhaust) Abnormal Signal - Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Electric Protection System Functional Test
3524B Engine for Caterpillar Built Machines Accessory Drive (Rear) - Remove
3408E and 3412E Industrial Engines Sensors and Electrical Components
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Oil Step Speed Calibration
3524B Engine for Caterpillar Built Machines Accessory Drive (Rear) - Install
Digital Voltage Regulator Instantaneous Trip Shutdown - Troubleshoot
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Magnetic Pickup Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Diode Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Engine Oil Pressure Switch Test
3600 Diesel Marine Monitoring System Safety Signs and Labels
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Slave Relay Test
3600 Diesel Marine Monitoring System Electrical System
3600 Diesel Marine Monitoring System Before Starting Engine