Inlet Manifold - Remove
Removal Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Disconnect electrical connector (5) for the air inlet heater, if necessary.
Show/hide table
Illustration 1 | g00545513 |
Typical example |
Show/hide table
Illustration 2 | g00545514 |
Typical example |
- Disconnect fuel line (6) from the air inlet heater.
- Remove two bolts (7) that hold the fuel line to inlet manifold (14) .
- Loosen two hose clamps (8) from the hose that connects the inlet manifold (14) to the turbocharger.
- Disconnect hose assembly (9) from the turbocharger.
- Remove four bolts (3) in order to remove elbow (2) and gasket (4) .
- Disconnect boost pressure inlet (10) from inlet manifold (14) .
- Remove bolts (12) that hold the turbocharger support to inlet manifold (14) .
- Remove bolts (13) that hold inlet manifold (14) to the cylinder head.
- Remove inlet manifold (14) and gaskets (11) .
- Remove seal (1) that covers the gap between inlet manifold (14) and the valve mechanism cover.
Caterpillar Information System:
3054 Engine for Caterpillar Built Machines Turbocharger - Assemble
G3606 and G3608 Engines Water Pump Seal - Remove
3054 Engine for Caterpillar Built Machines Turbocharger - Disassemble
3054 Engine for Caterpillar Built Machines Turbocharger - Install
3054 Engine for Caterpillar Built Machines Turbocharger - Remove
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Cooler - Install
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Pump - Remove
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles - Install
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles - Remove
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3054 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3612 and 3616 Fast Vessel Engines Hourly Performance Log
3606 and 3608 Engines Cooling System Operation
3054 and 3056 Industrial and Generator Set Engines Inlet Manifold - Install
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
G3606 and G3608 Engines Water Pump Seal - Install
3612 and 3616 Fast Vessel Engines Engine Mounts - Check
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Remove
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3612 and 3616 Fast Vessel Engines Air Shutoff - Test