 |
|
Diesel engine exhaust contains products of combustion which may cause personal injury. Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside. |
|
|
Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts. Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified. The machine must be parked on a level surface and the engine stopped. Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine. |
|
|
Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine. |
|
|
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Description | Qty |
| A(1) | 198-4234 | Digital Indicator | 1 |
| B(1) | 198-4236 | Adapter Cable As | 2 |
| C(1) | 198-4239 | Pressure Sensor Gp
0 to |
2 |
| D | 177-7860 | Hose As | 1 |
| 6V-4143 | Quick Connect Coupler | 2 | |
| E | 110-6349 | Fitting As | 2 |
| (1) | Tool (A =), Tool (B), and Tool (C) are part of the 198-4240 Digital Pressure Indicator Gp. |
- Drive the machine to a smooth, horizontal surface.
Show/hide table
Illustration 1 g06160408 - Move propel lever (1) to the NEUTRAL position.
- Move parking brake switch (2) to the ON position.
- Place the engine in ECO mode or low idle.
- Select "Main Menu" (3) on the machine display.
- Select "Machine Setup" (4).
Show/hide table
Illustration 3 g06148261 - Select "Engine Spd Sw" (5).
Show/hide table
Illustration 4 g06148286 - Select "ECO" (6) or "Low" (7).
Show/hide table
Illustration 2 g06148038 Show/hide table
Illustration 5 g06160422 - Move engine start switch (8) to the OFF position.
Show/hide table
Illustration 6 g06160385 - Unlock latch (9) and open engine compartment door (10) on the right side of the machine.
- Assemble the tooling. Connect Tool (B) to Tool (C). Assemble two sets of Tool (B) and Tool (C).
- Connect both sets of Tool (B) to Tool (A).
Show/hide table
Illustration 7 g06161928 - Connect one Tool (C) to port "Ma" (11) on the machine valve.
- Connect other Tool (C) to port "Mb" (12) of the machine valve.
Show/hide table
Illustration 8 g06161935 - Mark the connectors, then disconnect solenoid electrical connections (13).
Show/hide table
Illustration 9 g06161961 - Remove the plugs from port "X1" (14) and port "X2" (15). Install one Tool (E) in port "X1". Install other Tool (E) in port "X2".
- Assemble Tool (D).
- Connect one end of Tool (D) to Tool (E) in port "X1" (14). Connect other end of Tool (D) to Tool (E) in port "X2" (15).
- Move engine start switch (8) to the START position. Release the switch when the engine starts.
- Place the engine in high idle.
- Operate the hydraulic system until the oil temperature reaches the test temperature of
45 °C (113 °F) . - Place the engine in ECO mode or in low idle.
- Read pressure differential on Tool (A). The pressure differential should be within
200 kPa (29 psi) . If the pressure differential is within200 kPa (29 psi) , go to Step 21. If the pressure differential is not within200 kPa (29 psi) , go to Step 20.Show/hide table
Illustration 10 g06161966 - Use a pass through socket wrench to loosen lock nut (16) and rotate adjustment screw (17) until the pressure is equal. The pressures should be within
200 kPa (29 psi) . Hold the adjustment screw, and tighten the lock nut to a torque of20 N·m (15 lb·ft) . - Move engine start switch (8) to the OFF position.
- Remove tooling from port "Mb" (12) and port "Ma" (11) in the machine valve.
- Remove Tool (D) from port "X1" (14) and from port "X2" (15).
- Remove Tool (E) from port "X1" and from port "X2". Install plugs in port "X1" and port "X2".
- Connect solenoid electrical connectors (13).
- Close engine compartment door (10) on the right side of machine and secure latch (9).
