Manual Barring Group - 50:1 Reduction
Show/hide table
图 1 | g00322856 |
手动盘车总成 (1) 齿轮轴和润滑脂嘴 (2) 锁紧螺母 (3) 按钮 (4) 连接器 |
手动盘车总成使用电驱动马达,以便缓慢地转动发动机。 当进行维修作业时,使用手动盘车总成。
使用下列程序以便接合手动盘车总成:
- 松开锁紧螺母 (2)。
Show/hide table
注意 在小齿轮啮合和分离时,如果盘车组按钮不能完全向外拉,按钮轴将损坏小齿轮轴的O型密封圈。 当小齿轮啮合和分离时,确保按钮完全向外拉。
- 完全向外拉旋钮 (3),压下锁紧螺母 (2),直到螺母与壳体平齐。
注: 锁紧螺母 (2)是弹簧加载小齿轮轴的一部分。 如果锁紧螺母不能与壳体平齐,轴齿轮不能与飞轮齿圈齿轮啮合。 在螺母上保持向内的压力,仔细调整连接器 (4)。 沿顺时针方向或逆时针方向转动连接器。 调整可能需要连接器在任何方向转动一圈多。 调整连接器,直到锁紧螺母与壳体平齐。
- 锁紧螺母 (2) 与壳体平齐后,松开按钮 (3),缓慢从锁紧螺母撤走手压,直到按钮与小齿轮轴槽接合。
Show/hide table
注意 |
---|
不要使用冲击扳手来操作盘车装置。 使用冲击扳手来操作将导致齿轮齿损坏。 |
当手动盘车总成在接合位置,发动机起动系统不起作用。
为了转动发动机曲轴,使用马达控制。 手动盘车总成直接与电马达连接。 电马达产生曲轴在任何方向转动所需的扭矩。
如果仅仅转动发动机曲轴,大约需要
当轴 (1)上小齿轮与飞轮齿圈齿轮啮合时,发动机曲轴在锁定位置。
利用下列程序来分离手动盘车总成:
- 将按钮 (3)完全向外拉并按下锁紧螺母 (2), 直到轴 (1)上的弹簧移动小齿轮到分离位置。
- 确保小齿轮完全分离。
注: 当锁紧螺母 (2)经过壳体时,小齿轮完全分离。
- 小齿轮完全分离后,松开按钮 (3)。
- 将锁紧螺母 (2)拧紧到
70 ± 15 N·m (50 ± 11 lb ft) 的扭矩。
注: 如果轴 (1)不能完全分离,在任何方向上转动连接器 (4)。 在任何方向上转动连接器,降低小齿轮和飞轮齿圈齿轮之间的侧负载(摩擦)。
Show/hide table
注意 |
---|
直到盘车小齿轮完全从飞轮齿圈脱离之前,不要操作发动机起动马达。 会导致发动机严重损坏。 |
当手动盘车总成没有被启动,手动盘车总成必须从飞轮上分离,手动盘车总成必须固定在分离位置。
Caterpillar Information System:
G3606 and G3608 Engines Cooling System
3406E, C-10 and C-12 Truck Engines Fuel System Primary Filter - Clean/Replace
3618 Engine Engine Design
G3300 Engines Electrical System
G3500 Engines Ignition Systems
3406E Truck Engines Electronic Control System
Electronic Modular Control Panel II (EMCP II) For MUI Engines Engine/Generator Programming OP5
G3612 and G3616 Engines Hydraulic Actuator Position Sensor Calibration
G3606 and G3608 Engines Pressure Relief Valve Setting
3618 Engine Crankshaft Seals
3508, 3512 and 3516 Engines Fuel System
3406E Truck Engines Engine Vibration Troubleshooting
3512 Industrial Engine Extended Life Coolant (ELC)
3618 Engine Troubleshooting
3512 Industrial Engine Extended Life Coolant (ELC) Cooling System Maintenance
SPS342 Skid Mounted Pumper S·O·S Services Coolant Analysis
PM3412C Power Modules Fuel System Secondary Filter - Replace
3508, 3512 and 3516 Engines Air Inlet and Exhaust System
G3500 Generator Sets Control Panel
322B Excavator Hydraulic System General Testing and Adjusting Information
3618 Engine Piston and Rings
3508, 3512, and 3516 Generator Sets Generator Set Description
3500B and 3500B High Displacement Generator Set Engines Lubrication System Operation
3508, 3512 and 3516 Engines Basic Block