1996/09/02 Caterpillar


Improved Starter Solenoid Assemblies Available {1467,1518}

Usage:


Machines Using 3E-5449, 3E-7859, 3E-7770, 9X-4250, 9X-4823, 9X-9511, 105-4037, 105-4038 Starter Solenoid Assemblies

Reference: Service Manual Module; SENR3581; Delco Remy 37-MT, 41-MT, 42-MT Series Starting Motors

Description of Change: The listed starter solenoid assemblies have been changed to improve reliability by reducing the possibility of solenoid coil shorts and opens, as well as failures caused by moisture entry. These changes are:

1. A rubber washer has been added inside the solenoid to protect the solenoid coils against vibration.

2. The solenoid coils are held in place with an improved application of epoxy.

3. The plastic cap of the solenoids has been redesigned to prevent cracking which can lead to moisture entry and damage of the solenoid contacts. The improved solenoids can be visually identified by the change in plastic cap design. The previous cap design is identified by the small projection (1) toward the motor terminal side of the cap. The improved cap does not have this projection. See Illustrations 1 & 2.

Adaptable To:

The 3E-5449, 3E-7859, 3E-7770, 9X-4250, 9X-4823, 9X-9511, 105-4037, 105-4038 Starter Solenoid Assemblies have been improved effective with date code 6B01 (6 = year 96, B = February, 01 = 1st day) or 2/1/96. These improved starter solenoid assemblies are on starter motors with date code 96D15 (96 = year, D = April, 15 = 15th day) or 4/15/96. The 3E-5449, 3E-7859, 3E-7770, 9X-4250, 9X-4823, 9X-9511, 105-4037, 105-4038 Starter Solenoid Assemblies are a direct replacement for the previous versions and are in production on machines and engines using these starter motor and solenoid assemblies.

NOTE: On machines and engines equipped with 3E-7985 (24 volt), 8C-3663 (24 volt), and 8C-3662 (12 volt) Engine Shutdown Solenoids, a failure of the starter solenoid can cause a failure of the engine shutdown solenoid. If the starter motor remains energized, the engine shutdown solenoid will also remain energized and may fail since it is not a continuous duty solenoid.


Illustration 1. Previous Starter Solenoid Cap, (1) Small Projection.


Illustration 2. Improved Starter Solenoid Cap.

Caterpillar Information System:

1996/08/26 Explanation of "Pull Up Voltage" {0350}
1996/07/01 New Cleanout Filters Available For Hydraulic Systems And Drive Trains {5068}
1996/07/01 New Stop/Tail Lamp Groups Available {1429}
1996/06/17 Tamper-Proof Caps Available For Hydraulic Implement Pump Groups{5073}
1996/06/10 New U-Cup Seal And Spacer(s) Replace Cylinder Rod Packing Seal {5101,5102,5103,5104,5213,5223,5229,5265}
1996/06/10 New Ring Seal Material Used In Brake Groups For Improved Service Life {7555,4251}
1996/06/03 Improved Governor Servo Components Available For Use With Energize To Run Solenoids; Energize To Run Solenoid Stop Bolt Adjustment Procedure{1264,1259}
1996/06/03 U-Cup Rod Seals Available For Hydraulic Cylinders Used In Cold Temperatures{5102,5104}
1996/05/06 Starter Solenoid Assembly May Need New Terminal {1467,1518}
1996/04/29 New Element Assemblies Available Within Jacket Water Heater Groups{1383}
1996/04/29 Integral Connector Now Used On The Air Conditioning Condenser Fan Motor Relay Assembly{1408,7320}
1996/04/15 New Element Assemblies Available Within Jacket Water Heater Groups{1383}
1996/09/16 Snap Ring Retains Rod Wiper Seal In Several Hydraulic Cylinder Groups {7562,4303,5102,5104,5105,5106,5108,5141,5303,5352,5356,5452,5457,5458,5468,5555}
1996/09/16 Vibration Resistant LED Kit Available For Use With Back-Lit Rocker Switches {1429}
1996/09/16 Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/30 New Valve Cover Seals Are Used For Mechanical Unit Injector (MUI) And Electronic Unit Injector (EUI) Engines{1107}
1996/10/07 Parts Manuals May List Air Conditioning Compressors Incorrectly {1802,1809,7320}
1996/11/18 Measure Vibration Of Vibratory Compactor Drums With Hand Held Meters{7471,0783}
1996/11/25 Procedure For Installing Steel Core Gasket At The Front Housing And The Flywheel Housing {1151,1157,1162}
1996/12/09 Rotate Crankshaft On 3114, 3116 And 3126 Engines Using 9U-6943 Gear Shaft Housing Assembly Or 9U-7336 Gear Shaft Housing Assembly {1202,0701}
1996/12/09 Remove And Install Threaded Glands On Hydraulic Cylinder Using 9U-7868 Spanner Wrench Group, 9U-7869 Spanner Wrench Group, Eleven Adapter Plates (See Chart B){5456,0738}
1996/12/09 Thicker 1U-9646 Pusher And 1U-9647 Pusher Make XT-3 Hose Assembly Easier{0684}
1996/12/09 Electronic Control Training Aid{0713}
1996/12/09 124-0662 Impact Socket For Removing And Installing Cylinder Head Bolts{1100,0602}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.