Water Pump
Show/hide table
Illustration 1 | g06000509 |
Show/hide table
Specification for 349-6213 Water Pump Gp | |||
Item | Qty | Part | Specification Description |
B | 1 | 336-2212 Water Pump Seal As | Installation height of the seal is |
1 | 1 | 229-5469 Bearing Locknut | Torque to Use the following procedure in order to tighten the set screws of locknut : 1. Tighten the set screws in 180 degrees pattern to 2. Again, tighten the set screws in 180 degrees pattern to |
2 | 1 | 313-2760 Impeller | Bore of the impeller for new shaft is |
3 | 1 | 258-8726 Pump Shaft | Diameter of the pump shaft for impeller is |
Lubricate the shaft lightly with clean engine oil before pressing the impeller on the pump shaft. | |||
During assembly, pump shaft must be flush with the face of the impeller within ± |
|||
4 | 1 | 235-4643 Water Pump Seal | During assembly, Install the water pump seal dry into the pump housing. Install the water pump seal within 2 minutes after the water pump seal has been removed from the tube. Use the correct installation tool. Do not use hand pressure to install water pump seal. |
5 | 1 | 4N-1230 O-Ring Seal | Lubricate with P-80 or 5P-3975 Rubber Lubricant. |
C | - | - | Distance between the impeller and the pump housing is |
Caterpillar Information System:
C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet Air Temperature Is High
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Contains Water
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Consumption Is Excessive
Procedure to Configure VIMS 3G® On Certain Cat® Products {7601} Procedure to Configure VIMS 3G® On Certain Cat® Products {7601}
2012/10/04 Importance of Proper Valve Lash Setting {1102, 1121, 1123}
2012/10/03 Importance of Proper Valve Lash Setting {1102, 1121, 1123, 1209}
559C and 579C Knuckleboom Loaders General Information (Stabilizer System)
2012/10/30 A New Valve Lifter Assembly Is Used in 3500B and 3500C Engines {1209}
2012/10/03 A New Valve Lifter Assembly Is Used in 3500B Engines {1209}
CB-634D Paving Compactor Lubricant Viscosities
2012/10/23 New Permanent Coupling Assemblies Are Now Used for the Service Brake Group on 773G and 775G Quarry Trucks {4251}
2012/12/10 A New Mud Guard in the Fender Group Is Now Used on Certain 773G and 775G Quarry Trucks {4220, 7252}
C1.5 and C2.2 Engines for Caterpillar Built Machines Oil Consumption Is Excessive
C1.5 and C2.2 Engines for Caterpillar Built Machines Oil Contains Coolant
CB44B Vibratory Asphalt Compactor Propel System (Split Drum) General Information (Propel System) - Split Drum
CB44B Vibratory Asphalt Compactor Propel System (Split Drum) Operator Controls (Propel System) - Split Drum
C1.5 and C2.2 Engines for Caterpillar Built Machines Oil Contains Fuel
CB44B Vibratory Asphalt Compactor Propel System (Split Drum) Propel System Components - Split Drum
C1.5 and C2.2 Engines for Caterpillar Built Machines Oil Pressure Is Low
CB44B Vibratory Asphalt Compactor Propel System (Split Drum) Piston Pump (Propel) - Split Drum
793F AC Off-Highway Truck TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 793F AC Off-Highway Truck TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
415-4055 Ultrasonic Wear Indicator IV Group{0787, 7000} 415-4055 Ultrasonic Wear Indicator IV Group{0787, 7000}
C1.5 and C2.2 Engines for Caterpillar Built Machines Valve Lash Is Excessive
521B and 522B Track Feller Bunchers Engine Supplement Refrigerant Condenser - Remove and Install