Piston Motor (Rear Axle Lubrication) - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-1114 | Vacuum Cap | 1 |
Show/hide table
 |
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
 |
- Refer to Operation and Maintenance Manual, "System Pressure Release".
- Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 276 to 414 kPa (40 to 60 psi). This will pull a vacuum on the hydraulic system.
- Disconnect hose assembly (1) and hose assemblies (2) .
Show/hide table
 | |
| Illustration 1 | g01981934 |
- Remove bolts (3). Remove piston pump (4). Remove O-ring seal (5) .
Show/hide table
 | |
| Illustration 2 | g01981997 |
Installation Procedure
- Install piston pump (4) in the reverse order of removal.
Caterpillar Information System:
2011/11/30 A Manufacturing Process Improvement Increases the Service Life of the Axle Shafts on 777D and 777F Off-Highway Trucks {3259, 3282}
793F Off-Highway Truck (Command For Hauling) Machine Systems Gear Pump (Rear Axle Lubrication) - Remove and Install
793F CMD Off-Highway Truck Steering Electronic Control System Using Caterpillar Electronic Technician (ET) to Determine Diagnostic Codes
793F CMD Off-Highway Truck Steering Electronic Control System Diagnostic Capabilities
2011/11/30 New Hose Assembly Is Now Used for Hydraulic Oil Lines Group on 14M Motor Graders {5057}
416F, 420F and 430F Backhoe Loaders Capacities (Refill)
2011/12/14 Improved Tightening Procedure for the Adjustment Nut on the Pressure Reducing Valve is Now Used on Certain Motor Graders {5051, 5467}
793F CMD Off-Highway Trucks Hydraulic Oil Filter - Replace - For Command Steering Valve
521B and 522B Track Feller Bunchers Capacities (Refill)
420F, 428F, 430F, 432F, 434F, 444F and 450F Backhoe Loaders Machine Electronic Control System MID 039 - CID 2245 - FMI 06
420F, 428F, 430F, 432F, 434F, 444F and 450F Backhoe Loaders Machine Electronic Control System MID 039 - CID 2245 - FMI 05
422F, 428F, 432F, 434F and 444F Backhoe Loaders Lift Cylinder Brace - Connect and Disconnect
2011/12/26 Additional Wear Protection Is Now Used for Cab Wiring Harness on Certain Off-Highway Trucks {1408, 7301}
R3000H Load Haul Dump Indicators and Gauges - Test
R3000H Load Haul Dump Steering Lockout (STIC Steering) - Test
R3000H Load Haul Dump Fuel System Primary Filter (Water Separator) - Drain
R3000H Load Haul Dump Fuel System Primary Filter (Water Separator) - Replace
R3000H Load Haul Dump Fuel Tank Breather - Replace
R3000H Load Haul Dump Differential Thrust Pin - Check/Adjust
R3000H Load Haul Dump Oil Filter (Pilot) - Replace
R3000H Load Haul Dump Solenoid Valve (Parking Brake) - Test
R3000H Load Haul Dump Lift Arm Support Pins
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Vibratory Control
521B and 522B Track Feller Bunchers TA2 Technical Inspection{7000, 753T} 521B and 522B Track Feller Bunchers TA2 Technical Inspection{7000, 753T}