Piston Pump (Auxiliary) - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 5F-7344     | Block     | 1     |
5F-7345 | Screw     | 1     | |
8H-0663 | Bearing Puller Gp     | 1     |
Start By:
- Remove the auxiliary pump. Refer to Disassembly and Assembly, "Piston Pump (Auxiliary) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
- Remove O-ring seal (2) from auxiliary pump (1) .
Show/hide table
Illustration 1 | g00955834 |
- Remove bolts (3) and end cap (4) from auxiliary pump (1) .
Show/hide table
Illustration 2 | g00955835 |
- Remove gasket (5) from end cap (4) .
Show/hide table
Illustration 3 | g00955836 |
- If necessary, remove bearing cup (6) from end cap (4) .
- Remove bolts (7), gasket (8), and control kit (9) .
- Remove nut (10), adjuster (11), O-ring seal (12), spring (13), and seat (14) from control kit (9) .
Show/hide table
Illustration 4 | g00955840 |
- Remove control cylinder (15) .
Show/hide table
Illustration 5 | g00955843 |
- Remove valve plate (16) from cylinder block assembly (17) .
- Remove bolts (18) and trunnions (19) from housing (20) .
Show/hide table
Illustration 6 | g00955844 |
- Remove O-ring seal (21) from each of trunnions (19) .
Show/hide table
Illustration 7 | g00955845 |
- Remove cylinder block assembly (17) and the swashplate assembly as a unit from housing (20) .
Show/hide table
Illustration 8 | g00955846 |
- Use Tooling (A) and remove bearing (22) from the shaft.
Show/hide table
Illustration 9 | g00955847 |
- Remove swashplate (24) from shaft (23) .
Show/hide table
Illustration 10 | g00955848 |
- Remove thrust plate (25) from swashplate (24) .
Show/hide table
Illustration 11 | g00955849 |
- Use Tooling (A) and remove bearing (26) from shaft (23) .
Show/hide table
Illustration 12 | g00955935 |
- Remove cylinder block kit (27) from shaft (23) .
- Remove relief valve assembly (28) from housing (20) .
Show/hide table
Illustration 13 | g00955933 |
- Remove retaining ring (29) and lip seal (30) from housing (20) .
Show/hide table
Illustration 14 | g00955934 |
Caterpillar Information System:
2003/02/24 Serviceable Parts for the 166-0294 Work Tool Harness As {1408, 7000}
416D Backhoe Loader Fuel Tank Water and Sediment - Drain
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Piston Pump (Auxiliary) - Install
C15 and C18 Petroleum Generator Sets Fuel Conservation Practices
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
416D Backhoe Loader Tire Inflation - Check
3054C Industrial Engine Fuel Injection Lines - Remove and Install
247, 257, 267, 277 and 287 Multi Terrain Loaders Lower Machine Frame - Clean
RM-350B Road Reclaimer/Soil Stabilizer Maintenance Interval Schedule
2003/03/10 New Flash File Software Is Used for Product Link 151/201 {7620}
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Oil Filter (Power Train)
3054E Industrial Engine Glow Plugs - Remove and Install
3054C Industrial Engine Fuel Injection Nozzles - Remove
C11 and C13 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3054C Industrial Engine Fuel Injection Nozzles - Install
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems Location of Electrical Components (Auger Conveyor)
2004/05/03 New Midshaft Bearing Assemblies Now Used to Increase Service Life {3253}
PM-465 Cold Planer Additional Messages
789C Off-Highway Truck Machine Systems Summary of Revisions
AP-655C and BG-2255C Asphalt Pavers Machine Systems Hydraulic Schematic (Auxiliary Systems)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood Tilt Actuator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Belt Tensioner - Remove and Install