Usage:
NOTE: Any adjustment to the governor must be made only by a person approved by Caterpillar or by a Caterpillar Dealer.
(1) Torque for nut ... 12 ± 4 N·m (9 ± 3 lb ft)
(2) 6N8793 Spring:
Length under test force ... 19.05 mm (.750 in)
Test force ... 2.00 ± 0.13 N (.45 ± .03 lb)
Free length after test ... 41.9 mm (1.65 in)
Outside diameter ... 9.40 mm (.370 in)
Install Spring Washers As Shown
(3) Seat. Install a spring washer, flat washer and spring washer between seat (3) and spring (4) as shown.
(4) 9L6448 Spring for the governor:
Put force on spring of ... 22 N (5 lb)
Then add more force to make spring shorter by ... 22.86 mm (.900 in)
Total test force ... 73.0 ± 1.5 N (16.60 ± .34 lb)
Free length after test ... 56.9 ± 0.8 mm (2.24 ± .03 in)
Outside diameter ... 35.3 mm (1.39 in)
Color code (stripes) ... one green, one yellow
(4) 9L6449 Spring for the governor:
Put force on spring of ... 22 N (5 lb)
Then add more force to make spring shorter by ... 22.86 mm (.900 in)
Total test force ... 86.6 ± 1.8 N (19.46 ± .40 lb)
Free length after test ... 56.9 ± 1 mm (2.24 ± .04 in)
Outside diameter ... 35.23 mm (1.387 in)
Color code (stripes) ... one green, one brown
(5) Install a flat washer, spring washer and flat washer.
(6) Diameter of the outer surface of the cylinder (new) ... 38.100 ± 0.013 mm (1.5000 ± .0005 in)
Bore in the gear (new) ... 38.151 ± 0.013 (1.5020 ± .0005 in)
(7) Put marks in alignment on pinion, stop and gear before installing dowel.
(8) Bore in the bearing (new) ... 22.263 ± 0.038 mm (.8765 ± .0015 in)
Diameter of the gear at the hub (new) ... 22.187 ± 0.013 mm (.8735 ± .0005 in)
(9) Distance from the face of the plate to the bearing for the governor drive assembly ... 0.51 ± 0.25 mm (.020 ± .010 in)
(10) Dowel installation:
Angle A must be ... 54 ± 10 degrees
Dimension B must be ... 7.9 ± 0.5 mm (.31 ± .02 in)
(11) Install dowels to get a dimension of ... 5.6 ± 0.5 mm (.22 ± .02 in)
Control Shaft Bearings
(12) Bore in the governor control shaft bearings (after assembly) ... 15.761 ± 0.038 mm (.6205 ± .0015 in)
Diameter of the governor control shaft (new) ... 15.720 ± 0.008 mm (.6189 ± .0003 in)
(13) Distance between the bearings for the governor control shaft ... 60.58 ± 0.13 mm (2.385 ± .005 in)
(14) Distance from the face of the housing to the end of the bearing for the governor control shaft ... 43.38 ± 0.15 mm (1.708 ± .006 in)
Shutoff Shaft Bearings
(15) Bore in the shutoff shaft bearing (new) ... 12.713 ± 0.013 mm (.5005 ± .0005 in)
Diameter of the shutoff shaft (new) ... 12.637 ± 0.013 mm (.4975 ± .0005 in)
(16) Torque for insulator ... 4.5 ± 0.6 N·m (40 ± 5 lb in)
(17) Needle bearing.
(18) Distance from center of bolt hole to outside end of needle bearing (17) ... 92.86 ± 0.25 mm (3.656 ± .010 in)
(19) Distance from end of needle bearing (17) to inside of sleeve bearing ... 98.68 ± 0.25 mm (3.885 ± .010 in)
Install seals as shown.
Maximum endplay for shaft ... 1.02 mm (.040 in)