Installation Of 9N3829 Jacket Water Heater Group{1383} Caterpillar


Installation Of 9N3829 Jacket Water Heater Group{1383}

Usage:

1100, 3100, 3208

C/L - Centerline

The 9N3829 Jacket Water Heater Group can be installed on any of the above engines. The heater group has two 1000 Watt, 120 V heater elements, one for each side of the engine, to heat the coolant in the cylinder block. For those engines that are equipped with sound suppression panels, some modification must be made to a panel on each side of the engine before the heaters are installed. The modification procedure is given in this instruction.

NOTE: In the procedure that follows, all reference to left side or right side is made with the view as seen from the flywheel end of the engine.

1 Drain the coolant from the cylinder block. Remove the center core plug (1) from each side of the engine.

NOTE: For engines that have sound suppression panels, the centerline of the core plug must be found and marked, before removal of the panels. Find the centerline of the plug as follows:

A. On both sides of the cylinder block, measure along the surface of the panels, from the bottom edge of the cylinder block top deck (surface) for dimension (A), which is 5.70" (144.8).
B. Dimensions (B) and (C) are measured from the front face of the cylinder block. Dimension (B), for the right side of the cylinder block, is 12.39" (314.7). Dimension (C), for the left side of the cylinder block, is 13.39" (340.1). Put a mark on each panel at the point where dimensions (A) and (C) and (A) and (B) come together, (this is the approximate centerline for plugs (1) on each side of the engine).

2 Remove the sound suppression panels, if so equipped.

NOTE: Use the mark (found in step 1B) as the center, and make a hole approximately 2.50" Ø (63.5 Ø) in each panel.

3 Remove any paint, sealant or rough edges in or around the area of the bore where the core plugs were removed. Install 9N3834 Element (1), 6N9121 Gasket (2), 6N9119 Adapter (3), 3H1461 Seal (4), 6N9122 Split Ring (5), 6N9123 Plate (6) and 2R1980 Nut (7). Make sure that element (1) is not in contact with the inside of the cylinder block, and then tighten nut (7). Use the same procedure to install both elements (1).

NOTE: Install the sound suppression panels, if so equipped.

4 Install a 6N1604 Cap (8), as shown, for each element (1). NOTE: Caps (8) are used as dust covers when electrical cords (9) are removed for any reason.

5 Install the electrical cords (9) that come with the heater group. (Electrical cords (9) can either be two separate cords, or one 9N3830 Cord Assembly.) Be sure to put the terminals of cords (9) in alignment with the terminals of elements (1) before nuts (10) are tightened.

NOTE: For electrical supply to the heaters, use electrical wire and connections that have a minimum capacity of 20 amps.

Caterpillar Information System:

Use of Piston Pin Bearing Removal and Installation Tools{1218} Use of Piston Pin Bearing Removal and Installation Tools{1218}
Using The 5P-4150 Nozzle Testing Group{0782} Using The 5P-4150 Nozzle Testing Group{0782}
Welding Procedure For Sprocket Rim Replacement{4156} Welding Procedure For Sprocket Rim Replacement{4156}
5P8579 Air Conditioning Charging And Testing Tool Group{1802, 0768, 0774} 5P8579 Air Conditioning Charging And Testing Tool Group{1802, 0768, 0774}
INSTALLATION, OPERATION AND MAINTENANCE OF 9N3771 INJECTION GROUP (CETANE){1250} INSTALLATION, OPERATION AND MAINTENANCE OF 9N3771 INJECTION GROUP (CETANE){1250}
Installation Of Coolant Conditioner Group{1350} Installation Of Coolant Conditioner Group{1350}
5P6590 Tester Schematic{0785, 0709, 1406, 1408} 5P6590 Tester Schematic{0785, 0709, 1406, 1408}
Installation Of 7N4295 Rebuild Kit For Refrigerant Compressor - Clutch And Drive{1802} Installation Of 7N4295 Rebuild Kit For Refrigerant Compressor - Clutch And Drive{1802}
Service Information And Instructions For Use Of 5P3600 Hydraulic Flow Meter{0650, 5050} Service Information And Instructions For Use Of 5P3600 Hydraulic Flow Meter{0650, 5050}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782} Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Alignment of Two Bearing Generators{4450} Alignment of Two Bearing Generators{4450}
Using The 5P2160 Engine Horsepower Meter Arrangement<FONT SIZE=-1>*</FONT>{0781, 0782} Using The 5P2160 Engine Horsepower Meter Arrangement<FONT SIZE=-1>*</FONT>{0781, 0782}
Using The 4S6553 Engine Evaluation Test Group{0781} Using The 4S6553 Engine Evaluation Test Group{0781}
Installation Of General Electric GE-603K Generators, GTA-15, GTA-18, GTA-22, GTA-23, GTA-25 and GTA-26 Alternators{1000, 4450} Installation Of General Electric GE-603K Generators, GTA-15, GTA-18, GTA-22, GTA-23, GTA-25 and GTA-26 Alternators{1000, 4450}
Alignment Of Caterpillar Marine Transmissions And Marine Engines{1000, 3300} Alignment Of Caterpillar Marine Transmissions And Marine Engines{1000, 3300}
Dynamometer Test Specifications For Caterpillar Engines{1000} Dynamometer Test Specifications For Caterpillar Engines{1000}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250} Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Installation Of 8N9754 Fuel Heater Group{1296} Installation Of 8N9754 Fuel Heater Group{1296}
Alignment - General Instructions{1000, 3000, 3300, 4450} Alignment - General Instructions{1000, 3000, 3300, 4450}
Recommendations For Cold Weather Starting Of Engines Equipped To Operate Air Compressors And Drills{1000, 1450} Recommendations For Cold Weather Starting Of Engines Equipped To Operate Air Compressors And Drills{1000, 1450}
Use Of The 6V-7070 And 6V-7800 Multimeter{0785} Use Of The 6V-7070 And 6V-7800 Multimeter{0785}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782} Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Replacement Sprocket Rim Welding Procedure{4156} Replacement Sprocket Rim Welding Procedure{4156}
6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569} 6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.