1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 Caterpillar


5. Commissioning

Usage:

5.1 Introduction

This chapter describes the course of action to be followed when taking the gearbox into service. The respective notes on safety shall be duly observed.

5.2 Commissioning Activities


In case of emergency actuate EMERGENCY-OFF.

* Do not touch any rotating parts


When filling the gearbox take care that lubricants are not allowed to pollute the environment.


Make sure to preform oil changes immediately after standstill with the gearbox still being warm, to avoid any setting of solid particles.

Fill the gearbox with clean oil as specified under the heading lubrication.

At first oil fill, actual oil volume and specified oil volume may vary due to preservation oil remains in the gearbox.


Ensure that no dirt or other contaminants are allowed to enter the gearbox.


A list of oils approved by L+S is given in Appendix B.

Fill in oil through the screw indicated in the installation drawing.

Check the oil level before starting up the gearbox. The correct oil level can be ascertained through the opening in the gearbox housing, when the gearbox is not operating.

The maximum operating temperature is 90°C.

When the operating temperature has been reached, check the entire gearbox for tightness. This check can be performed while the gearbox is running.


The following checks must only be carried out when the gearbox is at a standstill.

After 10 hours of full load operation check all fastening screws and boltings for tightness.

Check whether all bolts of the gearbox are tight as required.

The first oil change is to be made after approx. 150 operating hours.

Further oil changes are to be made at intervals as per the Maintenance Schedule given in Chapter 7.3.

Caterpillar Information System:

1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 4. Mounting
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 3. Handling / Storage
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 2. Product Description
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 1. Preliminary Notes
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 E. Parts Lists
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Drawings
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Spare Parts List
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Spare Parts List
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Spare Parts List
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Order No.: 02006676, Denomination: BRAKE RELEASE VALVE
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Spare Parts List
1998295 PROPEL DRIVES FOR UNDERCARRIAGE 9Q5983 Spare Parts List
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 7. Maintenance
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 8 Dismantling
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 10. Spare Parts Ordering
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 A. Addresses
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 B. Lube Oils
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 2 LSN 935 1410 "Lube Oil Recommendation CLP ISO VG 22-680"
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 3 LSN 935 1420 "Recommendation for Motor Lube Oils HD SAE 30, 40, 50"
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 4 LSN 935 1430 "Recommendation for Motorcar Transmission Oil HYP SAE"
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 5 Viscosity Classification Comparison of Various Lubricants
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 6 Oil Change/Topping up Oil
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 7 Abbreviations and Symbols Used
1998303 PROPEL DRIVES FOR UNDERCARRIAGE 1692776, 9Q5874, 9Q5 8 References, Co-applicable DIN Standards
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.