SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Caterpillar


Mounting

Usage:

Introduction

This chapter describes the installation of the gearboxes.

The hydraulic motor has been mounted at the gearbox housing.


The preceding safety notes must be carefully observed.

Carefully follow the instructions given on the installation drawing: 1/6140/5138/2.

Mounting Work to be Performed


Secure the gearbox safely before removing the lifting straps or ropes.

* Avoid heavy blows when mounting the equipment.


Make sure that axial forces are not exerted during mounting.

* Make sure high compression forces do not act on the gearbox housing.
* During this work observe installation drawing as well as pertinent data.
Attach the gearbox to a crane.
Lift the gear into the bogie frame.
Tighten the screws using a torque wrench. The relevant tightening torques shall be taken from the frame drawing.
Remove the lifting or ropes.
Remove the plugs before connecting the hydraulic oil lines.


Make sure that no dirt or foreign bodies are allowed to enter the hydraulic system.

* Connect the hydraulic motor.


The preceding safety notes of customer must be carefully observed.

* Connect the multi-plate parking brake.


The multi-plate parking brake is a safety device of the gearbox.

* Connect the brake release line after removing the plug (item 39).


Make sure that no dirt or foreign bodies are allowed to enter the brake release port.


Make sure that the brake release port is properly sealed.

* Back pressure is not allowed in the brake release line.

Check once again tight fit of all joining elements.

Caterpillar Information System:

SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Handling / Storage
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Product Description
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Preliminary Notes
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Illustration
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO REMOVING THE SHAFT NUT FROM THE DRIVE
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Parts Lists
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Drawings
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Installation Notes for a Axial Piston Units
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Attachment Parts
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Lube Oils
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Addresses
SUPPLEMENTARY SERVICE INFORMATION FOR 149-3535 LOHMANN & STO Spare Parts Ordering
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Commissioning
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Maintenance
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Dismantling
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Spare Parts Ordering
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Lube Oils
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Safety regulations
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Repair Instructions
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Installation notes for axial piston units
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Drawings
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Spare Parts Lists
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Addresses
SUPPLEMENTARY SERVICE INFORMATION FOR 1C-7183 LOHMANN & STOL Removing The Shaft Nut From The Drive
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.